Results 1 to 10 of about 35,305 (120)
Comfort of Use Assessment in Buildings with Interior Wall Insulation Based on Silicate and Lime System in the Context of the Elimination of Mould Growth [PDF]
Archives of Civil Engineering, 2020 In the article, the authors presented the results of microbiological air quality studies in selected buildings with additional thermal insulation applied from the inside using a silicate and lime system, as well as the results of a survey study ...
Elżbieta Radziszewska-Zielina +3 more
doaj +1 more source
Case Report: Invasive Fungal Infection and Daratumumab: A Case Series and Review of Literature
Frontiers in Oncology, 2022 Life expectancy of multiple myeloma (MM) patients has improved in last years due to the advent of anti-CD38 monoclonal antibodies in combination with immunomodulators and proteasome inhibitors.
Francesca Farina +16 more
doaj +1 more source
Impact of Dehumidification Devices on Production Efficiency in Plastic Injection
Sakarya Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2021 One of the many methods used in the production of plastic materials is plastic injection method. The plastic injection method needs equipment difficult to choose, and it is also costly. Many negativities could be experienced during production.
M. Tahir Oktaç +2 more
doaj +1 more source
Risk factors for moisture damage presence and severity in Finnish homes
Buildings & Cities, 2023 Moisture-damaged buildings are a prominent issue in Finland, but with limited information on damage prevalence, degree of severity and risk factors. This paper analyses 14,996 Finnish detached and semidetached houses that have undergone a standardised ...
Jonathon Taylor +7 more
doaj +1 more source
Crystals, 2021 An experimental investigation has been carried out to analyse different mould section sizes to measure the meniscus fluctuation by varying different liquid flow rates and different submerged entry nozzle port angles, i.e., 0° port angles, 15° downward ...
Manish Kumar +2 more
doaj +1 more source
Metals, 2020 The continuous casting process (CCP) is the most vital part of steelmaking. The flow pattern near the submerged entry nozzle (SEN) and mould greatly influence the quality of the slab produced.
Manish Kumar +2 more
doaj +1 more source
Evaluation of Hydrothermal Treatment of Winter Wheat Grain with Ozonated Water
Plants, 2023 Products must be cleaned or otherwise treated to keep them clean when they are prepared for further production or when they are supplied fresh to the consumer. Cereals have significantly lower settling losses than succulent agricultural products, but the
Simona Paulikienė +1 more
doaj +1 more source
Thermal bridges in buildings as a result of urban transformation [PDF]
Facta Universitatis. Series: Architecture and Civil Engineering, 2013 The paper analyzes the deterioration of energy performance in buildings and construction defects caused by thermal bridges resulting from changes taking place in urban planning, for example in Vojvode Stepe street in Belgrade.
Rajčić Aleksandar
doaj +1 more source
MYCOLOGICAL STATUS OF SOME DAIRY PRODUCTES SERVING IN ASSIUT UNIVERSITY HOSPITALS [PDF]
Assiut Veterinary Medical Journal, 2014 A total of 60 random samples of yoghurt and feta cheese (30 of each ) were collected from Food Department in Assiut University hospitals from July, to October, 2013 for estimation the counts and identification of total yeasts and moulds in yoghurt and ...
NAGAH, M. SAAD, YASSER, S. WAFY
doaj +1 more source
Archives of Metallurgy and Materials, 2017 The composites made of continuous fibers in the form of unidirectional and fabric prepregs are widely used in many fields of engineering for the production of lightweight and durable parts or whole structures. To achieve this, we not only need to possess
Golewski P., Sadowski T.
doaj +1 more source