Results 171 to 180 of about 47,967 (247)

A U‐shaped Microfluidic Platform for Culturing Vascularized Colorectal Cancer Spheroids Reveals Tumor–Endothelial Crosstalk and Invasion‐Associated Remodeling

Advanced Materials Technologies, EarlyView.
A closed U‐shaped microfluidic platform symmetrically embeds a single, size‐controlled HT29 colorectal cancer spheroid within a GFP‐HUVEC‐laden fibrin matrix. HT29 spheroids are associated with hyper‐branched endothelial network remodeling, while vascularized co‐culture is accompanied by anisotropic protrusive growth and EMT‐like marker changes in the ...
G. Cretti, M. Ballerini, A. Mantegazza, P. Occhetta, M. Rasponi   +4 more
wiley   +1 more source

Controlled hot pressing for functional upcycling of waste polyethylene materials. [PDF]

Sci Rep
Cheng D, Yan WJ.
europepmc   +1 more source

Programmable Variable‐Stiffness Multilayer Elastomer Composites With High‐Aspect‐Ratio Low‐Melting‐Point Alloy Inclusions

Advanced Materials Technologies, EarlyView.
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane, Gyan Edbert Zesiro, Hao Zhou, Gursel Alici, Mu Chiao   +4 more
wiley   +1 more source

Warpage of Injection-Moulded Thin Plates: Numerical Evaluation of Simulation Strategies and Experimental Validation. [PDF]

Polymers (Basel)
Kastelic T, Mole N, Cafuta G, Starman B, Halilovič M.   +4 more
europepmc   +1 more source

Hybrid Additive Manufacturing of Highly Stretchable Bottlebrush Polymer Nanocomposites by Decoupled Extrusion and Photopatterning

Advanced Materials Technologies, EarlyView.
A Hybrid Direct Ink Writing–Digital Light Processing (HDD) strategy decouples material extrusion from shape definition, enabling high‐fidelity additive manufacturing of highly viscous, yield‐stress polymer nanocomposites. Excess ink acts as a removable, self‐supporting scaffold, allowing fabrication of unsupported and embedded complex architectures ...
Shahryar Ramezani Bajgiran, Emmanuel Oduro, Daniel A. Rau, Li‐Heng Cai   +3 more
wiley   +1 more source

Mechanical Performance Investigation of Recycled HDPE Reinforced with Nanoclay for Enhanced Strength and Sustainability. [PDF]

Polymers (Basel)
Rajendran S, Sankaran S, Palani G, Niemczewska-Wójcik M, Sundaresan TK, Marimuthu U, Karuppiah K.   +6 more
europepmc   +1 more source

Photoluminescence Reshaping via Structural Confinement and Local Density of Optical States Control in Ir(III)‐Doped Biodegradable Metasurfaces

Advanced Materials Technologies, EarlyView.
Phosphorescent biodegradable metasurface showing vibronic selection and spectral photoluminescence narrowing. Anti‐correlation between experimental LDOS and measured lifetimes. ABSTRACT Metasurfaces incorporating phosphorescent emitters offer a route to engineer radiative and vibronic processes beyond chemical design.
Vincenzo Caligiuri, Andrea Smeriglio, Svetlana Siprova, Olga Favale, Francesca Leone, Roberto Termine, Debora Policastro, Alessandra Crispini, Attilio Golemme, Nicolas Godbert, Iolinda Aiello, Antonio De Luca   +11 more
wiley   +1 more source

Preparation and Structural Evolution of ZrB₂-HfC-SiC/Dicyanobenzene Hybrid Ultra-High-Temperature Materials Moulded at 250 °C/2 h. [PDF]

Materials (Basel)
Wang J, Zhu X, Mu X, Wang B.
europepmc   +1 more source

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

Advanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina, Adam Tam, Jennifer Lam, Nila C. Wu, Nancy T. Li, Alison P. McGuigan   +5 more
wiley   +1 more source

Polymer Melt Stability Monitoring in Injection Moulding Using LSTM-Based Time-Series Models. [PDF]

Polymers (Basel)
Costa P, Mendes SP, Loureiro P.
europepmc   +1 more source