Results 131 to 140 of about 24,810 (288)
Polymer Composites, EarlyView.An experimental multiscale approach to investigate how fiber spacing, orientation, and material hybridization influence fiber‐matrix debonding and transverse cracking. ABSTRACT This study aims to experimentally quantify fiber‐matrix debonding and transverse crack evolution in single‐fiber and double‐fiber composite specimens, with particular emphasis ...
Zaynab Hazaveh, Behrad Koohbor
wiley +1 more source
Polymer Composites, EarlyView.Composite cylinder under axial and radial compression. ABSTRACT This study examines the hygrothermal degradation of filament‐wound glass fiber‐reinforced epoxy composite tubes designed for application as liners in oil and gas systems, focusing on their response under axial or radial compression.
Anderson L. dos Santos +3 more
wiley +1 more source
Polymer Composites, EarlyView.Graphical representation of the wear‐mode‐dependent tribological behavior of graphene nanoplatelet (GNP) modified glass fiber‐reinforced epoxy composites, highlighting the distinct mechanisms governing dry sliding wear and solid particle erosion. ABSTRACT Glass fiber‐reinforced epoxy composites are widely used in structural applications where surface ...
Elif Gültürk +2 more
wiley +1 more source
Polymer Composites, EarlyView.Preparation of lightweight composite panels from multilayer beverage carton waste. ABSTRACT Beverage carton waste, a multi‐layer composite of cardboard, polymer, and aluminum, presents significant recycling challenges for conventional recovery technologies. This work presents a manufacturing process‐oriented method that allows shredded beverage cartons
Csenge Tóth +2 more
wiley +1 more source
Biodegradable materials as foundry moulding sands binders
Metalurgija, 2015 The aim of this article is to show the possibility of using biodegradable materials as part of the composition of foundry moulding and core sand binders. Research shows that moulding sands with biodegradable materials selected as binders are not only less toxic but are also better suited to mechanical reclamation than moulding sands with phenol ...
openaire +2 more sources
Polymer Engineering &Science, EarlyView.This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan +5 more
wiley +1 more source
Influence of foundry dust on moulding mixtures quality
Metalurgija, 2013 The objective of this paper was to observe the effect of the addition of the dust from the moulding plant on the quality parameters of the moulding mixtures and determine tolerable content in the moulding mixture.
A. Pribulová +4 more
doaj
Sustainable Development, EarlyView.ABSTRACT Additive Manufacturing (AM) has been identified as a potential catalyst for a paradigm shift within the construction industry, due to its capacity to enhance sustainability, reduce waste, and augment design flexibility. This study presents a systematic literature review (SLR) that explores the application of Life Cycle Assessment (LCA) in ...
Antonio Mastropasqua +3 more
wiley +1 more source
Influence of a Reclaimed Sand Addition to Moulding Sand with Furan Resin on Its Impact on the Environment. [PDF]
Water Air Soil Pollut, 2016 Holtzer M, Dańko R, Kmita A.
europepmc +1 more source
steel research international, EarlyView.The study investigates the influence of DED‐Arc/M versus casting on the microstructure and material properties of X40CrMoV5‐1 (AISI H13) hot‐work tool steel. DED‐Arc/M yields finer microstructures, superior mechanical strength, and ductility, but slightly reduced thermal conductivity.
Ulf Ziesing +4 more
wiley +1 more source