Results 221 to 230 of about 1,339 (303)

The production, properties and casting potential of a clay/oil-bonded foundry moulding sand

, 1978
Peter A.E. Hill
openalex   +1 more source

Surface wear and roughness of experimental composites containing calcium orthophosphate particles following toothbrush abrasion

European Journal of Oral Sciences, Volume 134, Issue 2, April 2026.
Abstract This study evaluated experimental composites containing dicalcium phosphate dihydrate (DCPD) particles for toothbrush wear and roughness. Composites containing bisphenol‐A glycidyl dimethacrylate/triethylene glycol dimethacrylate with 50 vol% inorganic fraction consisting of barium glass and DCPD (35:15 and 15:35 vol%) or barium glass only ...
Handially S. Vilela, Mariana C. A. Resende, Leticia O. Sakae, Amanda L. Campos, Tais Scaramucci, Roberto R. Braga   +5 more
wiley   +1 more source

Effect of steel slag as fine aggregate on the mechanical and durability performance of concrete under acid exposure. [PDF]

Sci Rep
Khan A, Luqman M, Jun X, Ullah MF, Alzlfawi A, Ahmad M, Toth Z.   +6 more
europepmc   +1 more source

Strengthening Potentials of Lithium‐Doped Soda–Lime–Silicate Glasses Through Surface Crystallization of Quartz‐ss

International Journal of Applied Glass Science, Volume 17, Issue 2, April 2026.
ABSTRACT The formation of a crystallized surface layer, having a lower coefficient of thermal expansion (CTE) than the parent glass, can be exploited to place the glass surface under compression during cooling from crystallization temperature and hence improve mechanical properties.
Fabian Stoelzel, Thorsten Gerdes
wiley   +1 more source

Porosity and cement controlling the response of artificially cemented tailings under hydrostatic loading to high pressures. [PDF]

Sci Rep
Consoli NC, de Azambuja Carvalho JV, Wagner AC, Carvalho I, de Sousa Silva JP.   +4 more
europepmc   +1 more source

Analysis and assessment of foundry moulding sand preparing process using the dynamic power measurement method

, 2010
E. Źiółkowski, R. Wrona, K. Smyksy
openalex   +1 more source

Analysis of Influence of Sand Matrix on Properties of Moulding Compounds Made with Furan Resin Intended for 3D Printing [PDF]

Daniel Robert Gruszka, R. Dańko, M. Dereń, A. Wodzisz   +3 more
openalex   +1 more source

Water‐Borne Erosion of Reinforced Polymer Composites: Application to Shallow Offshore Marine Environment

Polymer Composites, Volume 47, Issue 5, Page 4102-4126, 10 March 2026.
Comparison of experimental and model‐predicted erosion rates for carbon fibre‐reinforced polymer (CFRP) and glass fibre‐reinforced polymer (GFRP) under low‐velocity (2 m/s) and at varying angles and sand concentrations (0.0, 0.05, 0.4 g/L). The results demonstrate good agreement between experimental data and model predictions across different erosive ...
Ali Al‐Darraji, Christopher Lagat, Thaneshan Sapanathan, Peter Butt, Ibukun Oluwoye   +4 more
wiley   +1 more source

Optimizing the Composition of Geopolymer Composites Incorporating Secondary Aluminium Industry By-Products Using Mathematical Modelling. [PDF]

Materials (Basel)
Sharko A, Le VS, Sharko O, Stepanchikov D, Srb P, Petrů M, Louda P, Movchan P, Łoś KE.   +8 more
europepmc   +1 more source

The Study on Moulding Sand for Cast Steel

DENKI-SEIKO[ELECTRIC FURNACE STEEL], 1963
I. Kori, K. Tominaga
openaire   +2 more sources