Results 31 to 40 of about 1,970 (307)

The Influence of Sand Grains Properties on Electrical Properties of Moulding Sand with Inorganic Binder

Archives of Foundry Engineering, 2015
The paper presents the results of basic research on the influence of the properties of sand grains on electrical properties of water glass moulding sands.
Opyd B., Granat K.
doaj   +1 more source

Impact of the Different Moulding Parameters on Properties of the Green Sand Mould

Archives of Foundry Engineering, 2022
Sand Casting process depends mainly on properties of the green sand mould, sand casting requires requires producing green sand mould without failure and breakage during separation the mould from the model, transportation and handling. Production of the green sand mould corresponding to dimensions and form of the desired model without troubles depends ...
openaire   +2 more sources

Artificial Neural Networks as a Tool for Supporting a Moulding Sand Control System Based on the Dependency between Selected Moulding Sand Properties

, 2023
The article presents the potential for using artificial neural networks to support decisions related to the rebonding of green moulding sand. The basic properties of the moulding sand tested in foundries are discussed, especially compactibility as it ...
Mrzygłód, Barbara, Opaliński, Andrzej, Regulski, Krzysztof, Jakubski, Jarosław   +3 more
core   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Polymer Binder BioCo3 with Silicates and its Application to Microwave-Cured Moulding Sand

Archives of Foundry Engineering, 2017
The effects of silica additive (Poraver) on selected properties of BioCo3 binder in form of an aqueous poly(sodium acrylate) and dextrin (PAANa/D) binder were determined.
Grabowska B., Kaczmarska K., Bobrowski A., Drożyński D., Żymankowska-Kumon S., Cukrowicz S.   +5 more
doaj   +1 more source

Multimodal Soft Surgical Robots Enabled by Eco‐Degradable, Sterilizable Polymers and Transient Electronics

Advanced Functional Materials, Volume 36, Issue 51, 25 June 2026.
A compostable PGS soft surgical robot with interchangeable modules integrates transient Mo tactile and Si thermal sensors for dual feedback. The device preserves its function after clinical‐grade sterilization, demonstrates stable actuation and cardiac tissue grasping with real‐time in vivo pulsatile monitoring, and biodegrades post‐use with soil‐safe, 
Minseong Chae, Kyung‐Sub Kim, Gyeong‐Seok Hwang, Jun‐Seok Shim, Sung‐Woo Kim, Yong‐Wu Kim, Jieun Han, Jae‐Young Bae, Jae‐Hwan Lee, Minjung Chae, Jooik Jeon, Joo‐Hyeon Park, You‐Jung Park, Ju‐Yong Lee, Sung‐Geun Choi, Min‐Ha Oh, Yong‐Joong Shin, Young‐In Ryu, Ji‐Woo Gu, Seong‐Yu Choi, Jeong‐Yun Sun, Jung Keun Hyun, Myoung‐Ryul Ok, Sang Yup Kim, Edyta Wyszkowska, Ju‐Young Kim, Kang‐Sik Lee, Seung‐Kyun Kang   +27 more
wiley   +1 more source

Selection of hardening technology of moulding sand with hydrated sodium silicate binder devoted to aluminum alloys ablation casting [PDF]

Archives of Metallurgy and Materials, 2019
The ablation casting technology consists in pouring castings in single-use moulds made from the mixture of sand and watersoluble binder. After pouring the mould with liquid metal, while the casting is still solidifying, the mould destruction (washing out,
K. Major-Gabryś, M. Hosadyna-Kondracka, A. Grabarczyk, J. Kamińska   +3 more
doaj   +1 more source

Bioinspired Mechanically Robust Organic–Inorganic Hybridized Bio‐Adhesives With up to 50% Inorganic Components by Bi‐Continuous Phase Engineering

Advanced Functional Materials, EarlyView.
A robust plant protein adhesive was prepared by fabricating a bi‐continuous organic–inorganic hybrid structure. Compared with traditional organic–inorganic hybrid adhesives, the addition amount of inorganic phase is increased from 0.2%–3.0% to 50%, and the strength and toughness are increased by 6 and 121 times, respectively.
Zheng Liu, Wenlong Luo, Xu Yang, Xin Zhang, Yuru Zhu, Jingchao Li, Jianzhang Li, Jing Luo, Zhezhe Zhou, Pingan Song, Qiang Gao   +10 more
wiley   +1 more source

Shaping Matter with Acoustic Waves: From Particles to Functional Structures

Advanced Functional Materials, EarlyView.
Acoustic‐directed assembly is reviewed as a materials‐oriented strategy for organizing particles, polymers, metals, and biological systems into functional structures. The review distinguishes reversible manipulation from permanent structure formation through medium fixation, particle fixation, and in situ material generation, highlighting routes toward
Avraham Kenigsberg, Shelly Zlotnikov, Maya Fiorentino, Yuval Elias, Ornit Nagler‐Avramovitz, Hagay Shpaisman   +5 more
wiley   +1 more source