Results 41 to 50 of about 106,612 (245)
Advanced Materials Technologies, EarlyView.Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina +5 more
wiley +1 more source
3D‐Printing Aided Rapid Prototyping of Pretensioned Tensegrity Structures for Robotic Applications
Advanced Robotics Research, EarlyView.Printing, injection molding, and assembly (PMA) is a method for rapid prototyping mesoscale, topologically complex, and tensioned tensegrity structures. In combination with PMA method, two mold design strategies: modular mold and compact channel layout, enable efficiency and scalability for tensegrity fabrication.
Yi Sun +3 more
wiley +1 more source
, 1960 The results of tests carried out on the moulding sands and bonding clays are presented in the following five chapters.
Director, NML
core +1 more source
Gases Emission From Surface Layers of Sand Moulds and Cores Stored Under the Humid Air Conditions
Archives of Foundry Engineering, 2017 A large number of defects of castings made in sand moulds is caused by gases. There are several sources of gases: gases emitted from moulds, cores or protective coatings during pouring and casting solidification; water in moulding sands; moisture ...
Kaźnica N., Zych J., Mocek J.
doaj +1 more source
A Monolithic Janus Hydrogel Pressure Sensor for Wearable Motion and Physiological Monitoring
Advanced Science, EarlyView.This work reports a monolithic Janus hydrogel pressure sensor featuring integrated conductive PEDOT and insulating PEGDA layers. The fabricated device achieves a rapid response time, a wide operating range, and good cyclic durability. The sensor demonstrates robust performance in tracking dynamic human joint motions, offering a scalable strategy for ...
Syed Atif Ali +7 more
wiley +1 more source
Advanced Science, EarlyView.A large‐area, noise‐resilient multiplexed triboelectric sensing garment based on a multilayer shielded architecture and SnS2 nanoflower‐engineered hybrid materials enables interference‐suppressed, high‐fidelity full‐body motion tracking, achieving 0.13% signal misrecognition, 57 dB electromagnetic noise attenuation, and >1.5 N threshold force, while ...
Beibei Shao +14 more
wiley +1 more source
Study of Moulding Sands to Create Three-Layer Magnesium Concrete
Environmental and Climate TechnologiesThe article is devoted to the problem of creating energy-efficient building materials for enclosing structures. The aim of the research is to develop a recipe and a method for moulding sands placing to create heat-insulating concrete of a multilayer ...
Miryuk Olga
doaj +1 more source
The Tendency of Moulding Sands to Generate Core Cracks [PDF]
, 2018 The constant growth of foundry modernization, mechanization and automation is followed with growing requirements for the quality and parameters of both moulding and core sands.
Major-Gabryś, K. +3 more
core +1 more source
Bio‐Inspired Gradient Coatings Enhance the Leading Edge Erosion Resistance of Wind Blades
Advanced Science, EarlyView.Rain‐induced erosion of the wind turbine blade leading edge poses a critical challenge to maintenance and operation. Here, we propose a bio‐inspired approach for erosion protection utilising a platelet‐reinforced polyurethane coating with a graded through‐thickness architecture.
Natalia Sofia Guevara‐Sotelo +2 more
wiley +1 more source
A methodology for shrinkage measurement in micro-injection moulding [PDF]
, 2013 The aim of this paper is to provide a method for measuring shrinkage in micro injection moulded (μ-IM) parts - no standardised approach being reported as yet in the literature.
Alcock, Jeffrey R. +2 more
core +1 more source