Results 171 to 180 of about 944,627 (333)

Effect of Boron Addition on Liquid Zinc Embrittlement of Heat Affected Zone in 490 MPa Grade Steels

, 2019
Masayuki Yamamoto, Keiji Murayama, Hongmei Li, Naoki Takata   +3 more
openalex   +2 more sources

Controlled Movement of Soft Actuators using Multi‐Responsive Microgel Arrays and Microcirculatory Systems

Advanced Functional Materials, EarlyView.
Microscale hydrogels (microgels) feature improved mass transport characteristics supportive of fast actuation and chemical tunability amenable to programmed stimuli response. A unique soft actuator architecture is realized by encapsulating microgels in soft microcirculatory systems which enable the convenient delivery of liquid stimuli for powering and
Nengjian Huang, Brennan P. Watts, Stephen A. Morin   +2 more
wiley   +1 more source

Short contact time CH4 partial oxidation over Ni based catalyst at 1.5 MPa

, 2021
Gianluca Pauletto, Mathilde Mendil, Nicole J. LiBretto, Paolo Mocellin, Jeffrey T. Miller, Gregory S. Patience   +5 more
openalex   +2 more sources

Geometry‐Dependent Adhesion in Transparent Monodomain Liquid Crystal Elastomers

Advanced Functional Materials, EarlyView.
Liquid Crystal Elastomers (LCEs) are emerging as exciting pressure‐sensitive adhesives. We examine adhesion in chemically identical elastomer films, exploring the influence of geometry (director orientation) and phase (nematic or isotropic). We demonstrate the potential of these aligned films as transparent, tunable, broad‐temperature‐range smart ...
Aidan Street, Devesh Mistry, Johan Mattsson, Helen F. Gleeson   +3 more
wiley   +1 more source

Analysis of Bond Strength of Bioceramic Sealer Following Irrigation with Chlorhexidine. [PDF]

Iran Endod J
Costa LG, Saldanha JM, da Silva-Filho JE, Aguiar BA, de Almeida Gomes F, Gurgel-Filho ED.   +5 more
europepmc   +1 more source

Spatially Tailorable Liquid Crystalline Elastomer Alignment During Digital Light Process 3D Printing

Advanced Functional Materials, EarlyView.
Here, we report the fabrication of 3D printable liquid crystalline elastomer (LCE) structures with spatially tailorable alignment domains within the same layer. This work addresses the long‐standing challenge of preparing complex 3D LCE architectures with patterned functional domains to achieve nonlinear deformations. Fabrication of multi‐domains in 3D
Adam Bischoff, Saman Jamshididana, Zach Miller, Kassandra Hernandez, Nicolas Gonsalves, Andre Olarra, Elliot Yoo, Jeremy A. Herman, Devin J. Roach   +8 more
wiley   +1 more source

Are MPAs effective? [PDF]

ICES Journal of Marine Science, 2017
openaire   +1 more source

Ceramic Particle‐Reinforced Medium‐Entropy Alloys With Outstanding Mechanical Properties Prepared by Novel Micro‐LPBF

Advanced Functional Materials, EarlyView.
An innovative medium entropy alloy (MEA) composite material was fabricated via micro laser powder bed fusion (μ‐LPBF) with appropriate nano‐ceramic particles doping and exhibited markedly improved overall performance, including synergistically enhanced strength and ductility, increased hardness and compressive strength, improved wear resistance and ...
Zhonglin Shen, Mingwang Fu
wiley   +1 more source

Insights Into Gut Barrier Dysfunction and Metabolic Alterations in Mycophenolate-Induced Enteropathy. [PDF]

Basic Clin Pharmacol Toxicol
Brossier C, Sauvage FL, Valencia-Schmitt C, Calco V, Villa P, Marquet P, Lawson R.   +6 more
europepmc   +1 more source

The structure of liquid water up to 360 MPa from x-ray diffraction measurements using a high Q-range and from molecular simulation

, 2016
Lawrie Skinner, Mirza Galib, John L. Fulton, Christopher J. Mundy, John B. Parise, Van Tuong Pham, Gregory K. Schenter, Chris J. Benmore   +7 more
openalex   +2 more sources