Results 121 to 130 of about 59,241 (298)

Beyond Passivation: Designing Structurally Tailored Artificial Interphases for High‐Energy Lithium‐Based Anodes

Advanced Materials Interfaces, EarlyView.
This review outlines critical engineering design rules for building artificial protective coatings on next‐generation lithium metal and silicon battery anodes. It highlights how balancing structural flexibility with strict electronic and ionic transport limits prevents early battery failure.
Surin Gupte, Vilas G. Pol
wiley   +1 more source

Coupling of the Monte Carlo iMC and OpenFoam codes for multiphysics calculations of molten salt reactors

Frontiers in Nuclear Engineering
This paper presents the development of a multiphysics coupled framework of Monte Carlo neutronics iMC and OpenFOAM Computational Fluid Dynamics codes for molten salt reactor (MSR) analysis.
Inyup Kim, Taesuk Oh, Yonghee Kim
doaj   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Flexible Pressure Sensor With Co‐Optimized Sensitivity and Linearity Based on Gradient Toroidal Microstructures

Advanced Materials Technologies, EarlyView.
A flexible piezoresistive pressure sensor with gradient toroidal CNT/PDMS microstructures is reported. The hierarchical geometry enables sequential electrode contact, achieving a sensitivity of 256.20 kPa−1 and linear response (R2 = 0.99) over 0–1000 kPa.
Rongmei Wang, Ruolin Liu, Ming Lei, Yifan Liu, Fengming Hu, Bing Ji, Chao Peng, Jianyi Luo, Bingpu Zhou   +8 more
wiley   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

Photoluminescence Reshaping via Structural Confinement and Local Density of Optical States Control in Ir(III)‐Doped Biodegradable Metasurfaces

Advanced Materials Technologies, EarlyView.
Phosphorescent biodegradable metasurface showing vibronic selection and spectral photoluminescence narrowing. Anti‐correlation between experimental LDOS and measured lifetimes. ABSTRACT Metasurfaces incorporating phosphorescent emitters offer a route to engineer radiative and vibronic processes beyond chemical design.
Vincenzo Caligiuri, Andrea Smeriglio, Svetlana Siprova, Olga Favale, Francesca Leone, Roberto Termine, Debora Policastro, Alessandra Crispini, Attilio Golemme, Nicolas Godbert, Iolinda Aiello, Antonio De Luca   +11 more
wiley   +1 more source

A Constraint‐Based Analytical Framework for Design‐Space Analysis and Material Screening of Tubular Multilayer Dielectric Elastomer Pumps for Extracorporeal Circulatory Applications

Advanced Materials Technologies, EarlyView.
A constraint‐based analytical framework maps the coupled effects of material properties, structural parameters, and operating conditions in tubular dielectric elastomer pumps for extracorporeal circulatory applications. The approach defines performance boundaries through mechanical, electrical, and hydraulic constraints and identifies feasible design ...
Yan Zhang, Amine Benouhiba, Yoan Civet, Yves Perriard   +3 more
wiley   +1 more source

Integrated Steady-State System Package for Nuclear Thermal Propulsion Analysis Using Multi-Dimensional Thermal Hydraulics and Dimensionless Turbopump Treatment

Energies
Nuclear thermal propulsion is an evolving technology that can be utilized for long-distance space travel. This technology yields the advantage of a high thrust and specific impulse, but requires an examination of the potential design adjustments ...
Rory Myers, Mark DeHart, Dan Kotlyar
doaj   +1 more source

Liquid Metal Resistive Sensing Architectures for Measuring Diaphragm Strain Responses on Obstructed Surfaces

Advanced Materials Technologies, EarlyView.
A liquid metal‐based strain‐sensing architecture to measure the deformation of a circular diaphragm against obstructed surfaces is formulated using finite element modeling and confocal imaging to establish the mechanical framework and is utilized to control diaphragm‐induced confinement on a bead array, as validated by biomolecular loading level ...
Abdullah‐Bin Siddique, Jui‐Hong Weng, Deng‐Kai Yang, Chia‐Fu Chou, Nathan S. Swami   +4 more
wiley   +1 more source

Parameter Investigation for Stamp Manufacturing of Complex 3D Geometries Using Nanoimprint Lithography

Advanced Materials Technologies, EarlyView.
Nanoimprint lithography can replicate complex 3D microstructures with undercuts using single‐layer polymer stamps of different elasticities. By combining experiments and simulations, T‐shaped geometries and suitable undercut radii were identified that minimize stress and defects during demolding.
Christos Julianos Karapatzakis, Selina Burkert, Cordelia Friederike Wittemann, Andreas Heinrich   +3 more
wiley   +1 more source