Results 191 to 200 of about 681,106 (299)

Failure Modes and Influencing Factors of Rubber O-Ring Seals in High-Pressure Hydrogen Environments. [PDF]

Polymers (Basel)
Lv Z, Yasin S, Shi J, Zeng S.
europepmc   +1 more source

METHOD OF THE SEISMIC FAILURE PROBABILITY EVALUATION OF THE STRUCTURE CONSIDERING MULTIPLE FAILURE MODES

Journal of Japan Society of Civil Engineers, Ser. A1 (Structural Engineering ^|^ Earthquake Engineering (SE/EE)), 2013
Katsuyuki SAKASHITA, Yukio SHIBA
openaire   +2 more sources

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Optimizing Operational Efficiency and Patient Satisfaction in Tumor Day Wards: An HFMEA-Based Process Redesign Study. [PDF]

Risk Manag Healthc Policy
Li R, Li J, Song L, Yuan F.
europepmc   +1 more source

Opportunistic maintenance and adaptation of warranty maintenance tasks for Power Plant equipment [PDF]

, 2014
Alkali, Babakalli
core  

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Interfacial Friction-Controlled Fiber Failure Modes for Toughness Enhancement of Engineered Cementitious Composites. [PDF]

Materials (Basel)
Zhang D, Yang Y, Wang Z, Wang L.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Influence of Welding Control Mode on the Joint Performance of Ultrasonically Welded Carbon Fiber-Reinforced Polycarbonate. [PDF]

Materials (Basel)
Zhang Z, Yang Y, Wei L, Ao S, Li Y.
europepmc   +1 more source