Results 151 to 160 of about 45,720 (280)

Recent Advances in Conductive Rubber Composites: Progress, Challenges, and Emerging Opportunities

open access: yesMacromolecular Rapid Communications, EarlyView.
This study reviews the recent advances in conductive rubber composites, focusing on key aspects such as material selection, conductive mechanisms, interfacial engineering, processing methods, vulcanization strategies, and practical applications. It also discusses current challenges and highlights emerging directions that are shaping the development of ...
Lu Yin   +3 more
wiley   +1 more source

Spinel Aluminate‐Based Heterojunctions as Photocatalyst: A Review

open access: yesChemistryOpen, EarlyView.
Spinel aluminates (MAl2O4; M = Zn, Mg, Ca, Sr) serve as robust platforms for designing heterojunction photocatalysts. Their stable lattices, tunable band structures, and efficient charge transport enable improved light‐driven carrier separation, significantly enhancing pollutant degradation efficiency in advanced photocatalytic systems.
Ancy Kurian, Sumathi Shanmugam
wiley   +1 more source

Impact and Post‐Impact Properties of Carbon Fiber Fabric Laminates Reinforced With Carbon Nanofibres

open access: yesPolymer Composites, EarlyView.
Carbon nanofiber addition on the low‐velocity impact response of carbon fiber laminates. ABSTRACT The use of carbon fiber reinforced polymers (CFRPs) is limited by their susceptibility to low‐velocity impact (LVI) damage. This study investigates the effect of incorporating 0.75 wt.% carbon nanofibres (CNFs) into the epoxy matrix of carbon fiber fabric ...
Paulo Santos   +2 more
wiley   +1 more source

Performance enhancement of polysiloxane-based nanocomposite TENGs through optimized MWCNT concentration. [PDF]

open access: yesFront Chem
Tene T   +9 more
europepmc   +1 more source

Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications

open access: yesPolymer Composites, EarlyView.
Bio‐based additives derived from lignin and spent coffee grounds (SCG) are used to enhance MWCNT dispersion in PLA composites, enabling improved electrical conductivity and reliable in material extruded strain‐gauge sensors. ABSTRACT In this work, three bio‐based additives, lignin, spent coffee grounds (SCG), and oil extracted from SCG (Ox‐SCG) were ...
Silvia Lage‐Rivera   +6 more
wiley   +1 more source

Impact of MWCNT Aspect Ratio on the Processing and Functional Properties of Buckypaper for EMI Shielding Applications. [PDF]

open access: yesACS Omega
da Silva TF   +11 more
europepmc   +1 more source

Distributed Strain Sensing Using Electrical Time Domain Reflectometry With Nanocomposites [PDF]

open access: yes, 2018
di Scalea, Francesco Lanza   +2 more
core  

Mechanical Characterization of CNT/PLA Parts via FFF Additive Manufacturing

open access: yesPolymer Engineering &Science, EarlyView.
Effects of infill density on microstructure and porosity of 3D printed CNT/PLA composites. ABSTRACT Fused filament fabrication (FFF) enables the production of complex thermoplastic components but is often limited by internal porosity and insufficient mechanical performance for structural applications.
Yiyun Wu   +4 more
wiley   +1 more source

Secondary electron microscopy and transmission electron microscopy studies of carbon nanotubes in C-Ni films

open access: yesOpen Physics, 2011
Kozłowski Mirosław   +3 more
doaj   +1 more source

Home - About - Disclaimer - Privacy