Results 181 to 190 of about 45,435 (280)

Using Lignin and Spent Coffee Grounds as Bio‐Additives in 3D‐Printable Poly Lactic Acid/Multi‐Walled Carbon Nanotube Composites for Advanced Electronic Applications

Polymer Composites, EarlyView.
Bio‐based additives derived from lignin and spent coffee grounds (SCG) are used to enhance MWCNT dispersion in PLA composites, enabling improved electrical conductivity and reliable in material extruded strain‐gauge sensors. ABSTRACT In this work, three bio‐based additives, lignin, spent coffee grounds (SCG), and oil extracted from SCG (Ox‐SCG) were ...
Silvia Lage‐Rivera, Ana Ares‐Pernas, M. Sonia Dopico‐García, Carlos M. Costa, Nelson Pereira, Senentxu Lanceros‐Mendez, María‐José Abad   +6 more
wiley   +1 more source

Determination of bisphenol a in doogh (a yogurt-based Iranian drink) by magnetic-SPE (MWCNT-Fe₃O₄)/GC-MS method and human health risk assessment. [PDF]

Sci Rep
Rezapour Z, Arabameri M, Shariatifar N, Hamedi H.   +3 more
europepmc   +1 more source

Electrospun Nanofibres for Load‐Bearing Composite Materials—A Review of Techniques, Mechanical Properties and Durability

Polymer Composites, EarlyView.
Electrospun nanofibre for load‐bearing composite materials. ABSTRACT Electrospun nanofibres are emerging nanomaterials prized for their scalability, high surface area to volume ratio and yield. Their effectiveness in improving the mechanical properties of fiber reinforced composites is widely reported. Nanofibres could activate multiscale toughness and
Usaid Ahmed Shakil, Petr Hájek
wiley   +1 more source

Secondary electron microscopy and transmission electron microscopy studies of carbon nanotubes in C-Ni films

Open Physics, 2011
Kozłowski Mirosław, Dłużewski Piotr, Kowalska Ewa, Czerwosz Elżbieta   +3 more
doaj   +1 more source

Micropatterned Composite Hydrogel Sheet with Surface Electronic Conductive Network for Ultrasensitive Strain Sensing. [PDF]

Gels
Chu R, Liu M, Liu W, Song Z, Li G, Yu D, Liu X, Wang H.   +7 more
europepmc   +1 more source

Rheological Properties of Polyether Ether Ketones Containing Multi‐Walled Carbon Nanotubes

Polymer Engineering &Science, EarlyView.
Rheology, Melt Flow, and Spinnability of PEEK‐MWCNT Melts After Compounding. ABSTRACT In this study, the rheological and melt‐flow behavior of polyether ether ketone (PEEK) filled with multi‐walled carbon nanotubes (MWCNTs) was investigated to evaluate its melt‐spinnability.
Toty Onggar, Chokri Cherif
wiley   +1 more source

<i>N</i>‑Alkylamino-Functionalized Multiwalled Carbon Nanotubes for Advanced Grease Applications: Stability and Tribological Enhancement. [PDF]

ACS Omega
Scudło I, Woch J, Ruczka S, Korasiak K, Sabura E, Gębura K, Blacha-Grzechnik A, Boncel S.   +7 more
europepmc   +1 more source

Mechanical Characterization of CNT/PLA Parts via FFF Additive Manufacturing

Polymer Engineering &Science, EarlyView.
Effects of infill density on microstructure and porosity of 3D printed CNT/PLA composites. ABSTRACT Fused filament fabrication (FFF) enables the production of complex thermoplastic components but is often limited by internal porosity and insufficient mechanical performance for structural applications.
Yiyun Wu, Victor Neto, Robertt Valente, Daniel K. K. Cavalcanti, Tiago Gomes   +4 more
wiley   +1 more source

Reinforcing Restorative Dentistry: The Dual Role of Carbon Nanotubes in Material Enhancement and Therapy. [PDF]

Int J Dent
Bapat RA, Bedia SV, Bedia AS, Kuan EKS, Parolia A, Abdulla AM, Bapat PR, Chaubal TV, Sahebkar A, Almalki WH, Kesharwani P.   +10 more
europepmc   +1 more source

Electrospun conducting polymers: recent trends and the transition towards a sustainable future

Polymer International, EarlyView.
This review discusses the electrospinning of conducting polymers, detailing procedures, fibrous morphologies, improved properties, applications in electronics, and challenges, while outlining future directions for nanofibre‐based devices in various fields.
Xenofon Karagiorgis, Sofia Sandhu, Peter J. Skabara, Ravinder Dahiya   +3 more
wiley   +1 more source