Performance Evaluation of MQL with Graphene Mixed Nano Fluids prepared at different Concentrations in Turning of Pure Titanium (TI6Al4V) Alloy [PDF]
E3S Web of Conferences, 2021 This paper presents an investigation into the minimum quantity lubrication mode with Nano fluid during turning of titanium (TI6AL4V) alloy. In heavy cutting conditions, minimum quantity lubrication (MQL) has been observed, that, Nano-cutting fluids which
Suresh S. +5 more
doaj +1 more source
A novel study on the influence of graphene-based nanofluid concentrations on the response characteristics and surface-integrity of Hastelloy C-276 during minimum quantity lubrication. [PDF]
Heliyon, 2023 In present investigation, the impact of nanoparticle concentration on the machining accomplishment of Hastelloy C-276 has been examined in turning operation.
Singh G +8 more
europepmc +2 more sources
Performance investigations for sustainability assessment of Hastelloy C-276 under different machining environments. [PDF]
Heliyon, 2023 Hastelloy is categorized as difficult to cut superalloy widely used in aerospace, nuclear reactor components and chemical industry because of its magnificent strength and higher heat efficiency.
Singh G +9 more
europepmc +3 more sources
Machining response of Ti64 alloy under Nanofluid Minimum Quantity Lubrication (NFMQL) [PDF]
E3S Web of Conferences, 2021 Rapid wear progression of cutting insert associated with attainment of excessive tool-tip temperature are indispensable causes which limit operational domain of cutting velocity during dry turning of Ti64 alloy.
Sahoo Sarthak Prasad, Datta Saurav
doaj +1 more source
Fluids, 2023 Lubrication and cooling in hard machining is an urgent and growing concern. The use of a suitable cooling lubrication condition is a crucial factor and has a great influence on the machining efficiency and the machined surface quality in hard machining ...
Ngo Minh Tuan +2 more
doaj +1 more source
Effects of the Tribological Behaviour of h-BN MQL Nano Cutting Fluid (NCF-MQL) on Turning Inconel 625 [PDF]
INCAS Bulletin, 2019 Minimum quantity lubrication (MQL) is currently a widely used lubricating technique during machining, in which minimum amount of lubricant in the form of mist is delivered to the machining interface, thus helps to reduce the negative effects caused to ...
Chinmaya PADHY, Pariniti SINGH
doaj +1 more source
Modeling of Nanolubricant‐Assisted Machining Process by using Multiple Regression Analysis
Journal of Nanomaterials, Volume 2023, Issue 1, 2023., 2023 Graphite, due to its hexagonally arranged crystal structure, is a preferred lubricant. The crystal structure within a planar condensed ring system indicates that the layers are stacked in a direction that is parallel to each other. Researchers have reported that the use of graphite powder as a lubricant during machining has exhibited promising results.
S. Srikiran +3 more
wiley +1 more source
Inconel 718 Turning Process Parameters Optimization with MQL Nanofluid Based on CuO Nanoparticles
Journal of Nanomaterials, Volume 2022, Issue 1, 2022., 2022 This study examined the effects of a minimum quantity lubrication (MQL) and a Cupric oxide‐ (CuO‐) based nanofluid on Inconel 718 machinability. Additionally, by using an MQL CuO‐based nanofluid during the turning process, Inconel 718’s tribological characteristics are optimised. The experimentation was done using the minimum quantity lubrication (MQL)
Pravin A. Mane +8 more
wiley +1 more source
Influence of the Viscosity of Nanofluids on Surface Roughness in End Milling of Nickel Alloys with Minimum Quantity Lubrication [PDF]
, 2023 Minimum Quantity Lubrication (MQL) using vegetable oils is considered a sustainable lubrication method, particularly for machining difficult-to-machine materials like nickel and titanium alloys.
Anwar Mahmood +5 more
core +1 more source
Optimal Approaches for Hard Milling of SKD11 Steel Under MQL Conditions Using SIO2 Nanoparticles
Advances in Materials Science and Engineering, Volume 2022, Issue 1, 2022., 2022 Productivity and quality are always two goals in the production process. In metal cutting, two prominent representatives of quality and productivity are roughness and material removal rate (MRR). In this study, the Response Surface method was used to perform single‐objective and multiobjective optimizations during the hard milling of SKD11 steel.
Quoc-Manh Nguyen +2 more
wiley +1 more source