Results 101 to 110 of about 96,948 (308)
Dihydromyricetin (DMY) has been encapsulated in delivery systems to address the solubility limitations of DMY in water and improve its bioavailability. Air-assisted electrospinning has been used as a novel technology to load DMY.
Yupeng Ren +5 more
doaj +1 more source
Two‐Way Shape Memory Polymer Composite Gripper for Adaptive Robotic Applications
A two‐way shape memory polymer (SMP) composite is developed with intrinsic shape‐changing capability driven solely by temperature, eliminating external actuation loads. Embedding the SMP in a low‐stiffness elastomeric matrix enabled reversible transformations during heating and cooling cycles.
Aamna Hameed, Kamran Ahmed Khan
wiley +1 more source
IntroductionPolylactic acid (PLA) is a synthetic polymer material with good biodegradability, biocompatibility, and bioabsorbability, electrospinning is a convenient and efficient method for preparing PLA nanofibers as wound dressing.
Xiangsheng Wang +11 more
doaj +1 more source
Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja +9 more
wiley +1 more source
Transparent microelectrode arrays enable simultaneous optical and electrical electrophysiology with high spatiotemporal resolution, allowing multimodal observations of dynamic biological systems. Advances in materials and device architectures improve device performance by addressing key trade‐offs between optical transparency, impedance, and ...
Michael Abraham Listyawan +6 more
wiley +1 more source
Electrospinning Chitosan-based Nanofibers for Biomedical Applications
Chitosan-based, defect free, nanofibers with an average diameter between 60 and 120 nm were fabricated via electrospinning a blended solution of low molecular weight chitosan (LMWC) and polyethylene oxide (PEO).
Queen, Hailey
core
Fabrication and Characterization of ZnO Nanofibers by Electrospinning
ZnO nanofibers were successfully prepared by electrospinning a precursor mixture of polyvinylpyrrolidone (PVP)/zinc acetate, followed by calcination treatment of the electrospun composite nanofibers.
Inn Khuan Ng +4 more
core +1 more source
Soft dielectric elastomer composites often face a trade‐off between enhanced dielectric properties and mechanical compliance. Here, a parallel‐aligned polyurethane nanofiber network embedded in PDMS creates a flexible, durable composite with increased permittivity, low modulus, and fatigue stability after 100,000 cycles.
Yi Ge +9 more
wiley +1 more source
Qi-Wei Fu,1,* Yun-Peng Zi,1,* Wei Xu,1 Rong Zhou,1 Zhu-Yun Cai,1 Wei-Jie Zheng,1 Feng Chen,2 Qi-Rong Qian1 1Department of Orthopedics, Changzheng Hospital, Second Military Medical University, 2State Key Laboratory of High Performance Ceramics and ...
Qian QR +7 more
core
This review summarizes moisture‐adaptive strategies that enable triboelectric nanogenerators (TENGs) to operate across diverse moisture conditions. It examines moisture‐management methods, including exclusion, directional transport, removal, and utilization, with charge‐regulation approaches based on interfacial, dielectric, and structural engineering.
Junzhe Gan +4 more
wiley +1 more source

