Results 201 to 210 of about 2,010 (256)

Effect of High Ni Content in Gas-Atomized Cu-Ni-Si Powders for Laser Powder Bed Fusion. [PDF]

Materials (Basel)
Trovato M, Arcieri N, Manfredi D, Gobber FS, Bhatt B, Martucci A, Biamino S, Montanaro L, Lombardi M, Fino P.   +9 more
europepmc   +1 more source

Stranding of a Hector's Beaked Whale (Mesoplodon hectori) (Gray 1871) From South Australia Unearths Novel Additional Teeth

Marine Mammal Science, Volume 42, Issue 2, April 2026.
ABSTRACT Most extant beaked whales have reduced dentition of one or two pairs of tusk‐like, mandibular teeth that erupt through the gum only in adult males. Additional teeth have been recorded in several species and genera. A juvenile Hector's beaked whale (SAMA M26434) having additional teeth was collected in South Australia and its skeleton and ...
Catherine M. Kemper, Carolina Loch, Ludwig Jansen van Vuuren, Jeremy Austin, David Stemmer   +4 more
wiley   +1 more source

High-throughput quantification of quasistatic, dynamic and spall strength of materials across 10 orders of strain rates. [PDF]

PNAS Nexus
Eswarappa Prameela S, Walker CC, DiMarco CS, Mallick DD, Sun X, Hernandez S, Sasaki T, Wilkerson JW, Ramesh KT, Pharr GM, Weihs TP.   +10 more
europepmc   +1 more source

Mechanical Insights Into Polymeric Multilayers Films Using Nanoindentation and the Structural Compliance Method

Strain, Volume 62, Issue 2, April 2026.
This study applies nanoindentation to resolve layer‐specific mechanical properties in photovoltaic backsheet multilayer polymers. Structural compliance correction reduces substrate flexure and edge artefacts, enabling reliable hardness and modulus mapping.
P. Christoefl, J. E. Jakes, J. Geier, G. Pinter, G. Oreski, D. Stone, C. Teichert   +6 more
wiley   +1 more source

Oxygen vacancy-induced strengthening and toughening in (K,Na)NbO₃-based piezoceramics revealed via nanoindentation. [PDF]

Nat Commun
Zhang Z, Yang B, Chen L, Zhang Z, Guo J.
europepmc   +1 more source

<i>In Situ</i> Reactive Printing of Aluminum Matrix Composite with Ultra-High Volume Fraction Reinforcement. [PDF]

3D Print Addit Manuf
Tian C, Moridi A.
europepmc   +1 more source

On the Mechanical Performance of an L-PBF 316l Part Using the Performance-Line Instrumented Indentation Test (PL-IIT). [PDF]

Materials (Basel)
Maizza G, Hafeez F, Varone A, Montanari R.   +3 more
europepmc   +1 more source

Influence of Spark Plasma Sintering Parameters on the Microstructure, Mechanical and Tribological Characteristics of Air-Milled Aluminum. [PDF]

Materials (Basel)
Ammari H, Le Gallet S, Cornuault PH, Herbst F, Geoffroy N, Chemingui M, Optasanu V.   +6 more
europepmc   +1 more source

Effect of Mo and B on Microstructure and Impact Toughness of Coarse Grain Heat-Affected Zone in Low-Carbon V-Ti-N Micro-Alloyed Steel. [PDF]

Materials (Basel)
Qiao M, Fan H, Wang S, Huang Y, Wang Q, Liu R.   +5 more
europepmc   +1 more source

Microstructure and Properties of Binderless μWC Obtained Using the Electroconsolidation Method. [PDF]

Materials (Basel)
Hevorkian E, Samociuk W, Rucki M, Krzysiak Z, Pieniak D, Nerubatskyi V, Chyshkala V, Lytovchenko S, Chalko L, Morozow D, Caban J, Kulich V.   +11 more
europepmc   +1 more source