Results 121 to 130 of about 964,471 (239)

Ultrathin Hydrogel Membranes Inspired by Soap Films Enable Physiologically Relevant Breathing Lung Models

Advanced Materials, EarlyView.
A soap‐film inspired strategy enables the fabrication of ultrathin yet robust GelMA‐PAAm membranes for breathing lung culture. The hydrogel membrane supports long‐term cyclic deformation under air‐liquid interface conditions, enabling physiologically relevant breathing motions of engineered lung tissue culture. ABSTRACT Breathing continuously stretches
Yunji Lee, Gwang Myeong Kim, Wookyeom Kim, Fenny Soetanto, Gyungin Ryu, Taehun Chung, Youn Soo Kim, Junmin Lee, Hwa‐Rim Lee, Sungjune Jung   +9 more
wiley   +1 more source

Neutron capture resonances in ¹⁴²Nd and ¹⁴⁴Nd

, 1997
Wisshak, K., Voss, F., Käppeler, F.
openaire   +2 more sources

Comparison of DermaGenius and In-House qPCR Methods for Detection of Recalcitrant Dermatophyte Infections: A Practical Approach for Dermatologists and Mycologists. [PDF]

Mycoses
Durdu M, Kaplan E, Bingöl O, Ünal N, Demircili ME, Spruijtenburg B, do Prado CM, Meijer EFJ, Ilkit M.   +8 more
europepmc   +1 more source

Mechanically Assisted Magnetic Actuation in Ceramic‐Based Microscrolls for Fast and Durable Soft Robotic Systems

Advanced Materials, EarlyView.
Ceramic‐based V2O5/Fe3O4 hybrid films are shaped into butterfly‐proboscis‐inspired microscroll actuators. Magnetic triggering initiates unrolling, while geometry‐programmed elastic strain energy drives rapid recoil, enabling fast, reversible, durable, and load‐bearing actuation under near‐field magnetic stimulation.
Semi Kim, Shravan R. Kousik, Petia Atanasova, Eberhard Goering, Joachim Bill, Zaklina Burghard   +5 more
wiley   +1 more source

Morphological and Chemical Characterization of a Novel Wild Tea Plant Resource with Naturally Low Caffeine and High Theobromine from Guangxi Province, China. [PDF]

Plants (Basel)
Ma Q, Yan Z, Yang X, Hou A, Liu Z, Gan S, Yang Y, Chen Y, Qiu R, Wu W.   +9 more
europepmc   +1 more source

Energy Band Alignment and Electro‐Optical Behavior of Nearly Unstrained Monolayer MoS2 Heterostructures With GaN

Advanced Materials Interfaces, EarlyView.
Large size (∼100 µm) monolayer MoS2 grown by LPI‐CVD on n‐GaN exhibit a high n‐type doping, very low strain, and a type‐I band alignment at MoS2/GaN interface. Photocurrent measurements under illumination with photon energies from ∼2 to ∼5 eV show superior electro‐optical performances of these MoS2/n‐GaN heterojunctions as compared to Ni/n‐GaN devices ...
Salvatore Ethan Panasci, Emanuela Schilirò, Giuseppe Greco, Patrick Fiorenza, Fabrizio Roccaforte, Fiorenza Esposito, Igor Píš, Federica Bondino, Antonino Madonia, Marco Cannas, Simonpietro Agnello, Luca Seravalli, Filippo Giannazzo   +12 more
wiley   +1 more source

Effects of Different Cooking Methods (Pan-Frying, Sous-Vide, Boiling, and Deep Frying) on Mineral Composition and In Vitro Bioaccessibility of Beef, Lamb, and Chicken Livers. [PDF]

Food Sci Nutr
Aksoy AS, Bekiroglu H, Arici M, Sagdic O.   +3 more
europepmc   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

1q25.3-q32.1 deletion causing multisystem developmental delay: a case report and literature review. [PDF]

Front Pediatr
Liu L, Yu R, Zhang W, Huang S, Huang T.
europepmc   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source