Results 61 to 70 of about 489,226 (264)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Approaching a Nearly Zero Energy Building Integrated with PCM by Optimization of Energy Sources

Buildings
In recent years, population growth, the enhancement of carbon emissions generation, and higher energy consumption have caused the movement to nearly zero-energy buildings.
Ali Sulaiman Alsagri
doaj   +1 more source

The way to limit emission – energy efficient buildings. The example of the largest facility in Poland in nearly

Przegląd Naukowy Inżynieria i Kształtowanie Środowiska, 2020
In Szczecin a mixed-use complex Posejdon is being constructed. It will be the first nearly zero-energy building (NZEB) in Poland that meets the strict ecological standards that all buildings will have to meet after January 2021. The project was presented
Ewa Figiel, Dorota Leciej-Pirczewska
doaj   +1 more source

Experimental Nearly Zero Energy Building with Green Technology – Renovation Pilot through Passive House Expertise [PDF]

E3S Web of Conferences, 2019
The paper presents the preliminary planning of a demonstration pilot for exemplary renovation of an existing building (“Solar House 1 – Campina”) towards nZEB level using Passive House principles and technologies.
Petran Horia, Varga Szabolcs, Fogas Noémi   +2 more
doaj   +1 more source

Optimization of the sustainability during the refurbishment design phase of a residential building using SBToolpt-H [PDF]

, 2014
As it has been observed along the years, the unsustainability of the built environment is due to the high resources consumption and low indoor air quality of the existing building stock.
Mateus, Isabel, Mateus, Ricardo, Silva, Sandra Monteiro   +2 more
core   +1 more source

Nanoindentation Criteria for Combinatorial Thin Film Libraries

Advanced Engineering Materials, EarlyView.
Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley   +1 more source

3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs

Advanced Engineering Materials, EarlyView.
This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu, Nelson Pereira, Javier Vicente, Carmen Rial Tubio, Senentxu Lanceros‐Méndez   +4 more
wiley   +1 more source

The Role of Natural Ventilative Cooling in NZE Temporary and Emergency Shelters Design: a Mediterranean Case Study [PDF]

, 2016
The paper presents a case-study of a pre-fabricated housing module built in Messina (Sicily, Italy) and the assessment of its energy performances under the net zero energy perspective.
Antonucci, V, CELLURA, Maurizio, Ferraro, M, GUARINO, Francesco, LONGO, Sonia, Mistretta, M, Tumminia, Giovanni   +6 more
core  

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source

A Benchmark for a New Nearly Zero Energy Wooden Building in Europe

Drvna Industrija
To mitigate dangerous climate change, a drastic reduction of CO2 emissions is needed by 2030. Buildings contribute significantly to emissions, with the use phase of existing buildings being responsible for the majority of energy consumption. In addition,
Erwin Schau, Eva Prelovšek Niemelä
doaj   +1 more source