Results 51 to 60 of about 2,044 (211)

Failure behaviors and processing maps with failure domains for hot compression of a powder metallurgy Ni-based superalloy

Journal of Materials Research and Technology, 2022
Processing maps are key to guiding the thermo-mechanical processing (TMP) of superalloys. However, traditional processing maps are incapable of delimiting failure, which is an essential factor to be concerned about during the TMP of superalloys ...
Zonglin Chi, Shuai Ren, Jingbo Qiao, Jinglong Qu, Chengbin Yang, Zhuanye Xie, Wei Chen, Hua Zhang, Liang Jiang, Shuying Chen, Fanchao Meng   +10 more
doaj   +1 more source

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

The influence of additive manufacturing on Portevin-Le Châtelier (PLC) effect in Ni–Co-based superalloy

Journal of Materials Research and Technology
The microstructures and tensile properties of the Ni–Co-based superalloys made by additive manufacturing (AM) were investigated. The results revealed that both normal and inverse Portevin-Le Châtelier (PLC) effects were observed in AM Ni–Co-based ...
Ling Tang, Lei Xu, Yang Li, Jianping Tan, Changyun Li, Jinguo Li, Jingjing Liang, Chuanyong Cui, Xiaofeng Sun   +8 more
doaj   +1 more source

Assessment of the feasibility of determining the volume fraction and characteristics of the size, shape and distribution of γ’ phase precipitates in nickel-based superalloys

Technical Transactions, 2023
This overview presents a comprehensive exploration of the research methods employed for the precise assessment of volume fraction and the detailed characterisation of the size, shape and distribution of γ’ phase precipitates within Ni-based superalloys ...
Szczotok Agnieszka
doaj   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Kinetics and Mechanisms of γ′ Reprecipitation in a Ni-based Superalloy [PDF]

Scientific Reports, 2016
AbstractThe reprecipitation mechanisms and kinetics of γ′ particles during cooling from supersolvus and subsolvus temperatures were studied in AD730TM Ni-based superalloy using Differential Thermal Analysis (DTA). The evolution in the morphology and distribution of reprecipitated γ′ particles was investigated using Field Emission Gun Scanning Electron ...
Masoumi, F., Shahriari, D., Jahazi, M., Cormier, J., Devaux, A.   +4 more
openaire   +3 more sources

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source