Results 81 to 90 of about 746,464 (231)

A New Phenomenon: Sub-Tg, Solid-State, Plasticity-Induced Bonding in Polymers

, 2015
Polymer self-adhesion due to the interdiffusion of macromolecules has been an active area of research for several decades [70, 43, 62, 42, 72, 73, 41]. Here, we report a new phenomenon of sub-Tg, solid-state, plasticity-induced bonding; where amorphous ...
Padhye, Nikhil, Parks, David M., Slocum, Alexander H., Trout, Bernhardt L.   +3 more
core   +1 more source

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khaleghian, Anahita Emami   +3 more
wiley   +1 more source

Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing

Advanced Engineering Materials, EarlyView.
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Stryker Osteonics: Prosthetic Knee Joint [PDF]

, 2008
We examine, within a simple bearing model of a knee joint that only consideres pure sliding, the effect of the presence of a small vertical hole in the load area on the fluid film properties.
Hjorth, P.G., King, J., Korobeinikov, A., Mason, J., McKee, S., Wilson, S.   +5 more
core  

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source