Results 191 to 200 of about 247,758 (295)

Degradation Characteristics of Microstructure and Mechanical Properties on the Cross-Section of a Massive Casting Made of G17Mn5 Steel. [PDF]

Materials (Basel)
Kalandyk BE, Boroński D, Maćkowiak P, Trepczyńska-Łent M, Kasińska J, Sobula S.   +5 more
europepmc   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Exothermic Effects and Viscosity of Oxide Melts Formed During High-Temperature Reduction of Cr-Mn Ore Systems. [PDF]

Molecules
Makhambetov Y, Kabylkanov S, Abdulina S, Zhakan A, Burumbayev A, Sadyk Z, Akhmetov A, Saulebek Z, Toleukadyr R, Smagulov A, Yücel O.   +10 more
europepmc   +1 more source

Study on the Identification of Non-metallic Inclusions in Steel

Journal of the Japan Institute of Metals, 1962
openaire   +2 more sources

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

How high can the fatigue strength of metals be achieved? [PDF]

Natl Sci Rev
Xu Z, Su X, Zhang P, Wang B, Qu Z, Wang A, Zhang Z.   +6 more
europepmc   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Comparative Evaluation of Induction Furnace Steel Rebars: Mechanical Properties, Microstructure, and High-Temperature Corrosion Behavior in Seawater. [PDF]

Materials (Basel)
Chandio A, Channa IA, Shah AA, Pervez T, Ahmed W, Feroze S, Shar MA, Alhazaa A, Chandio AD.   +8 more
europepmc   +1 more source

A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle, Cesar Alvarez‐Llamas, Vincent Motto‐Ros, Christophe Dujardin, Jérémie Margueritat, David Rodney   +5 more
wiley   +1 more source

Quality, Microstructure and Properties of Metal Alloys (Second Volume). [PDF]

Materials (Basel)
Lipiński T.
europepmc   +1 more source