Results 131 to 140 of about 428,558 (290)
Advanced Engineering Materials, EarlyView.Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De +3 more
wiley +1 more source
α- and β-myosin II can be non-uniformly distributed within the cardiac sarcomere
iScienceSummary: In humans, the forces of the heartbeat are generated by both “fast” α-myosin II and “slow” β-myosin II molecular motors. Here, we report that α-myosin II and β-myosin II can take on an anisotropic arrangement within cardiac sarcomeres, the ...
James B. Hayes +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley +1 more source
A novel fixed-time prescribed performance sliding mode control for uncertain wheeled mobile robots
Scientific ReportsThis paper proposes a novel fixed-time prescribed performance sliding mode control method, specifically designed to address trajectory tracking issues in wheeled mobile robots (WMRs) affected by wheel slipping, skidding (WSS), and external disturbances ...
Van-Cuong Nguyen, Seong Han Kim
doaj +1 more source
On residual cumulative generalized exponential entropy and its application in human health
Electronic Research ArchiveNumerous adaptations of traditional entropy concepts and their residual counterparts have emerged in statistical research. While some methodologies incorporate supplementary variables or reshape foundational assumptions, many ultimately align with ...
Hanan H. Sakr, Mohamed S. Mohamed
doaj +1 more source
Advanced Engineering Materials, EarlyView.In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann +2 more
wiley +1 more source
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
PhotonicsThis study examines the physical-layer security of an indoor visible light communication (VLC) system using spatial modulation (SM), which consists of several transmitters, an authorized receiver, and a passive adversary.
Yahya M. Al-Moliki +3 more
doaj +1 more source
Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study
Advanced Engineering Materials, EarlyView.This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud +7 more
wiley +1 more source