Results 51 to 60 of about 1,216,491 (294)

Controlling Grain Growth in Powder Bed Fusion of Yttria‐Stabilized Zirconia Using Femtosecond Lasers: Challenges and Methodological Insights

open access: yesAdvanced Engineering Materials, EarlyView.
Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn   +5 more
wiley   +1 more source

Effects of intermodulation distortion on the performance of a hybrid radio/fiber system employing a self-pulsating laser diode transmitter [PDF]

open access: yes, 2003
A self-pulsating laser is used to generate a multicarrier (five radio frequency (RF) channels) microwave optical signal for use in a hybrid radio/fiber system. The self-pulsation is achieved by external light injection into the laser diode.
Anandarajah, Prince M.   +2 more
core   +2 more sources

Optimal Transmission of VLC System in the Presence of LED Nonlinearity and APD Module Saturation

open access: yesIEEE Photonics Journal, 2018
We address the optimal transmission of LED-based visible light communication (VLC) system using direct current biased optical orthogonal frequency division multiplexing (DCO-OFDM) modulation and avalanche photodiode (APD) receiver.
Meijun Gao, Chao Li, Zhengyuan Xu
doaj   +1 more source

Control Design and Experimental Validation of a HB-NPC as a Shunt Active Power Filter

open access: yesEnergies, 2020
This work presents the design of a control law based on the average model of a shunt active power filter considering an H-bridge neutral point clamped topology and its experimental validation. Therefore, the proposed controller is formed by three control
Gerardo Escobar   +5 more
doaj   +1 more source

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

open access: yesAdvanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz   +4 more
wiley   +1 more source

Nonlinear distortion analysis for multisine excitation constrained by power spectral density

open access: yesJournal of Measurement Science and Instrumentation, 2016
Nonlinear distortion introduced by an amplifier when subjected to a multisine excitation decreases the measurement accuracy in many metrological and measurement areas.In this paper,we performed qualitative and quantitative analyses of the nonlinear ...
ZHOU Kun-li, QU Ji-feng, ZHOU Zhen-yu
doaj  

Adaptive Pre-Distortion Compensation for LED Nonlinear Distortion in VLC-OFDM Systems Using Frequency Symbol Spreading

open access: yesApplied Sciences
This paper proposes an adaptive pre-distortion method for mitigating LED nonlinear distortion in Visible Light Communication (VLC)-OFDM systems. The inherent nonlinear characteristics of LEDs disrupt the orthogonality among OFDM subcarriers, causing ...
Koichi Seimiya   +3 more
doaj   +1 more source

Design of a Multistable Finger Prosthesis with Programmable Metamaterials

open access: yesAdvanced Engineering Materials, EarlyView.
This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz   +5 more
wiley   +1 more source

Reactive Current Reshaping With Series Resonance Damping for Three-Phase Buck-Type Dynamic Capacitor

open access: yesIEEE Access, 2019
By adding Buck-type AC/AC converter to conventional power capacitor, dynamic capacitor (D-CAP) can be formed to compensate variable rather than fixed reactive power.
Qi Wu   +5 more
doaj   +1 more source

A Multi‐Scale Machine Learning Framework for the Inverse Design of High Entropy Alloys

open access: yesAdvanced Engineering Materials, EarlyView.
High‐entropy alloys offer vast potential for various applications, including electrocatalysis; however, their compositional complexity challenges conventional screening. We introduce an inverse‐design framework combining two neural networks to determine optimal compositions and reconstruct nanoparticle geometry from targeted properties and conventional
Mikael Takoutsin   +14 more
wiley   +1 more source

Home - About - Disclaimer - Privacy