Results 181 to 190 of about 201,100 (277)
Advanced Materials Technologies, EarlyView.An in situ electroplating approach for MEX 3D printing is proposed, enabling copper deposition during the fabrication of conductive polymers. The method combines a printer‐integrated plating head, ML‐based g‐code control, and stop‐and‐go printing, achieving near‐bulk copper conductivity and enabling fully embedded, assembly‐free electronic components ...
Gianluca Percoco +5 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.One‐dimensional C4N2H14PbBr4 is shown to have a quasi‐direct electronic band structure and strongly anisotropic transport with polarized broadband emission. A GW/Bethe–Salpeter excited‐state force formalism, supported by polarized Raman and temperature‐dependent photoluminescence, identifies low–frequency Pb–Br phonons that drive ultrafast exciton self‐
Rijan Karkee +7 more
wiley +1 more source
A Pressure Microsensor Made of Parylene‐C for Use as Medical Implant
Advanced Materials Technologies, EarlyView.A monolithic parylene‐C pressure sensor with gold strain gauges provides 6.2 μV$\mu{\rm V}$·mmHg$\cdot{\rm mmHg}$−1$^{-1}$ sensitivity. The morphology of a sputtered thin film strain sensor is granular/columnar, which results in a high gauge factor of 7.5. Thermal bonding and parylene‐C coating create a hermetic cavity.
Ann‐Kathrin Klein +2 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.ABSTRACT Quantifying oral polymorphonuclear neutrophils (oPMNs) is a clinically validated approach for assessing periodontal inflammation. However, current methods, such as manual hemocytometry and flow cytometry, are time‐consuming (>3 h), require invasive sampling, and depend on staining and complex instrumentation, making them unsuitable for point ...
Mohsen Hassani +9 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.A MEMS‐integrated metamaterial filter enables continuous, low‐voltage spectral tuning in the long‐wavelength infrared (LWIR). The device employs extraordinary optical transmission in a dual suspended metasurface stack, where electrostatic actuation precisely controls the intermembrane air gap.
Oleg Bannik +6 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Image pixels are converted into optical pulse sequences to stimulate the optoelectronic synaptic device, generating dynamic responses that form high‐dimensional features. These features improve classification efficiency and demonstrate strong potential for neuromorphic edge computing systems.
Jo‐Lin Chen +3 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.This study shows that a lightweight blackbox neural network provides a practical, cost‐effective solution for bidirectional process prediction in laser‐induced graphene (LIG) fabrication. Achieving high predictive performance with minimal overhead, the approach democratizes machine learning (ML) for resource‐limited environments.
Maxim Polomoshnov +3 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.A flexible pressure sensor utilizing a 3D dual‐pore polyurethane structure is developed to overcome the intrinsic trade‐off between sensitivity and linearity. By inducing sequential buckling through distinct pore sizes and shapes, the device achieves highly linear and sensitive responses across a wide pressure range.
Jae Yeong Jang, Jaemin Choi, Young Jung
wiley +1 more source
Advanced Optical Materials, EarlyView.A dual‐domain PSLC architecture enables direct comparison of alignment‐dependent laser damage within a single device. Crack‐like and seal‐like morphologies emerge under different damage conditions, and their evolution is interpreted through quantitative image analysis and heat‐driven simulations.
Dengcheng Chen +4 more
wiley +1 more source