Results 121 to 130 of about 310,302 (319)
Quantum Dot and Hole Formation in Sputter Erosion
, 2000 Recently it was experimentally demonstrated that sputtering under normal incidence leads to the formation of spatially ordered uniform nanoscale islands or holes.
Barabasi, A. -L., Jeong, H., Kahng, B.
core +1 more source
Advanced Engineering Materials, EarlyView.This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures
Advanced Engineering Materials, EarlyView.This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Anti-periodic extremal problems for a class of nonlinear evolution inclusions in R N [PDF]
, 2014 Jingrui Zhang +3 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source