Results 81 to 90 of about 5,669 (252)
Evaluation of Heat Resistance Characteristics of Fibrous Material for Cold Weather Application [PDF]
Mechanics of Advanced Composite StructuresThe denier, cross-section, mass density, porosity, and depth of the nonwovens are the nonwovens' physical characteristics that depend on the thermally resistant layer.
Mithil Bangera +3 more
doaj +1 more source
World production and trade in nonwovens
, 2010 In the first chapter the diploma work describes the use and production of nonwovens. It proofs the importance and significance of this industry in world economy.
Strnad, Jiří
core
Porosity and barrier properties of polyethylene meltblown nonwovens [PDF]
, 2017 There are several areas in which textiles have been highly desirable due to their specific and high performance for many industries and sectors including in civil engineering, automobile, medicine, filtration, and electronics.
Yesil, Yalcin, Bhat, Gajanan S.
core +1 more source
Mass Spectrometry Reviews, EarlyView.ABSTRACT The use of MALDI mass spectrometry for the analysis of carbohydrates and glycoconjugates is a well‐established technique and this comprehensive review is the twelfth update of the original article published in 1999 and brings coverage of the literature to the end of 2024.
David J. Harvey
wiley +1 more source
One-step melt blowing process for PP/PEG micro-nanofiber filters with branch networks
Results in Physics, 2019 Polyethylene glycol (PEG) was inserted into polypropylene (PP) in one-step melt blowing process to strengthen the filtration quality of the melt-blown nonwovens. The micro-nanofiber nonwovens with branch structure were fabricated by controlling the ratio
Heng Zhang +4 more
doaj +1 more source
Polymer Composites, EarlyView.Veil interlayers of five different chemistries (PI, FG, PPS, PEI, PEEK) were placed at two through‐thickness positions in carbon and glass fiber/epoxy laminates and evaluated under interlaminar shear (ILSS), three‐point bending (3PB) and axial buckling loading. The optimum placement was found to be loading mode dependent: near‐surface placement favored
Yavuz Selim Tarih +3 more
wiley +1 more source
Fundamental studies on poly(trimethylene terephthalate) spunbonded nonwovens [PDF]
, 2001 Spunbonding is the most productive of all the non-conventional methods of textile fabric formation. Isotactic polypropylene is the most widely used polymer in spunbonding production because it is the least expensive fiber-forming polymer that provides ...
Zhao, Weili
core
Polymer Composites, EarlyView.Reinforcement where it matters: from a homogenious fiber‐reinforced part to a load‐adapted hybrid molded composite part. ABSTRACT Nonwoven composites based on flax fiber (NF)‐reinforced polypropylene (PP) offer a promising route toward sustainable lightweight structures but are limited by moderate mechanical performance.
Florian Tautenhain +4 more
wiley +1 more source
Polymer Engineering &Science, EarlyView.Schematic representation of the fabrication of thermoplastic composites using reused post‐consumer denim fabric and PLA and PP matrices via hot press molding. ABSTRACT The increasing generation of textile waste and the growing demand for sustainable materials have made the development of polymer composites reinforced with reused post‐consumer textiles ...
Umit Koc +3 more
wiley +1 more source
Improvement of Mechanical Properties of PCL Nanofibers Through Thermo‐Compression Process
Polymer Engineering &Science, EarlyView.Thermo‐compression enhances interfiber connectivity and mechanical properties of electrospun PCL nanofibers by controlling temperature, pressure, and duration, with the resulting behavior interpreted using the Deborah number. ABSTRACT Recently, polymeric nanofibers have been widely used in various fields, including electronics and optics, filtration ...
Min Jae Seo +2 more
wiley +1 more source