Results 121 to 130 of about 263,726 (280)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Revista Facultad de Ingeniería Universidad de Antioquia, 2013 This article develops numerically the advection-diffusion equation problem, using Galerkin on characteristic lines and Streamline Upwind Petrov-Galerkin (SUPG) methods. The dominated advective conditions in the solved problem showed that for cases where
Carlos Humberto Galeano +2 more
doaj
Are Mediators Norm Entrepreneurs? Exploring the Role of Mediators in Norm Diffusion
, 2017 Mediators are expected to include or uphold a growing number of norms in their interventions. For instance, inclusivity, gender equality, transitional justice, democracy promotion and the implementing instruments that accompany them are increasingly incorporated into the strategies of international and regional organizations, states and non-state ...
Hellmueller, Sara +2 more
openaire +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source