Results 291 to 300 of about 438,680 (418)

Atmospheric and submerged bone cement erosion by a pulsating water jet with a straight tubular nozzle extension. [PDF]

Sci Rep
Hloch S, den Dunnen S, Nag A, Souček K, Foldyna J, Tuijthof G, Gupta M, Pude F.   +7 more
europepmc   +1 more source

INLET NOZZLES FOR SLURRY FOR HRT BLANKET

, 1957
J M Trummel
openalex   +2 more sources

Miniaturized Devices for On‐the‐Spot Generation of Small‐Diameter Vascular Grafts

Advanced Materials Technologies, EarlyView.
An intracorporeal extrusion device is developed for on‐the‐spot generation of vascular grafts with tunable diameters spanning from 1 to 6 mm. The device uses biomimetic polymers and light, to promptly obtaining biocompatible and high‐burst pressure‐resistant grafts.
Deyanira Hernandez‐Sanchez, Maxime‐Emmanuel Comtois‐Bona, Antony El‐Khoury, Sergio David Garcia Schejtman, Aidan Macadam, Juan‐David Figueroa‐Alegria, Jesus M. Calderon‐Torres, Irene Guzmán‐Soto, Marc Ruel, Erik J. Suuronen, Marcelo Muñoz, Emilio I. Alarcon   +11 more
wiley   +1 more source

Studies on the Characteristics of Radial-Flow Nozzles : (1 st Report, Theoretical Analysis of Outward Flow)

, 1962
Tatsuya Hagiwara
openalex   +4 more sources

An advanced CNN-attention model with IFTTA optimization for prediction air consumption of relay nozzles. [PDF]

Sci Rep
Min S, Ning S, Yongbo C, Xiaoshuang X, Xuezheng Y, Zhen W, Lianqing Y.   +6 more
europepmc   +1 more source

On the Generation of Uniform Drops with Rotating Nozzles

, 1956
Yasusi TANASAWA, Tosio KURABAYASI, Yosirô Saitô   +2 more
openalex   +2 more sources

Enhanced Performance 3‐D Printed PLA Parts through a Photo‐Initiator Mediated UV‐Curing

Advanced Materials Technologies, EarlyView.
This solvent‐free method enhances 3‐D printed PLA parts by incorporating photo‐initiators during fabrication, followed by up to 3 min UV treatment. This process improves PLA's mechanical properties, including a 64% increase in tensile strength, while addressing weak interlayer bonding and outdoor sensitivity.
Dylan Jubinville, Tizazu H. Mekonnen
wiley   +1 more source

Investigation of the Influence of Manufacturing on Filament Production and Its Impact on Additive Manufactured Structures. [PDF]

Polymers (Basel)
Refat M, Maertens R, Weiss P, Henning F, Schulze V, Liebig WV.   +5 more
europepmc   +1 more source

Recent developments in spraying nozzles

, 1958
Richard J. Watts
openalex   +2 more sources

Stopping a Multilayered Co‐Axial Flow in a 3D Printed Microchannel with Cascaded Nozzles

Advanced Materials Technologies, EarlyView.
A microfluidic device with cascaded nozzles is 3D‐printed using two‐photon polymerization. Its microchannel, featuring integrated nozzles, sculpts multilayered co‐axial flows, enabling independent regulation of four co‐flowing streams to achieve variable layer thicknesses.
Helen Werner, Ebrahim TaiediNejad, Mehmet Akif Sahin, Moritz Leuthner, Peer Erfle, Oliver Hayden, Andreas Dietzel, Ghulam Destgeer   +7 more
wiley   +1 more source