Results 181 to 190 of about 6,161 (263)

Aerodynamic Optimization of Relay Nozzle Using a Chebyshev KAN Surrogate Model Integration and an Improved Multi-Objective Red-Billed Blue Magpie Optimizer. [PDF]

Biomimetics (Basel)
Shen M, Zhang Z, Qin G, Zhou D, Du L, Yu L.   +5 more
europepmc   +1 more source

Influence of Annealing Temperature on the Thermomechanical Properties and Dimensional Stability of FFF‐Printed PET‐CF

Journal of Applied Polymer Science, EarlyView.
Following extrusion at 265°C, components underwent a 45‐min annealing process at temperatures from 145°C to 225°C. The results show that increasing the annealing temperature elevates the onset of thermal softening, significantly enhancing thermal reliability.
Robin Mähnert, Matthias H. Deckert, Alexander Melzer‐Bartsch, Simon J. Heienbrock   +3 more
wiley   +1 more source

Effect of the Injector Pressure-Building Process on Dynamic Gas Flow Characteristics of a Highly Turbulent Underexpanded Hydrogen Jet from a Single-Hole Cylindrical Injector. [PDF]

ACS Omega
Sang H, Ye Y, Lei Y, Zhu Z, Kou C, Liu X, Qiu T.   +6 more
europepmc   +1 more source

Process Optimization of Solution Blow Spinning for Poly (N‐Isopropylacrylamide) Fibers

Journal of Applied Polymer Science, EarlyView.
Solution blow spinning has emerged as a safe and scalable technique for fabricating thermoresponsive PNIPAM fibers. The influence of key parameters on jet stability and fiber uniformity is determined through both rheological analysis and statistical process optimization. A Box–Behnken design reveals an optimized window for producing PNIPAM fibers below
Maryam Parastar, Filipe de Almeida Araujo, Uttandaraman Sundararaj   +2 more
wiley   +1 more source

Optimization of specific spray volume for spray application in pomegranate orchard using response surface methodology. [PDF]

Sci Rep
Thorat DS, Mehta CR, Agrawal KN, Jyoti B, Kumar M, Chandel NS.   +5 more
europepmc   +1 more source

Material Characterization of Lignin‐Filled Polypropylene Composites

Journal of Applied Polymer Science, EarlyView.
Ground and spray‐dried lignin powders are compared as fillers for polypropylene composites. Differences in powder preparation methods are associated with differences in powder characteristics and composite behavior after melt compounding. Spray‐dried lignin produces smaller particles and fewer large agglomerates, while a 5 wt% lignin loading provides a
Sungjun Hwang, Stefan N. E. Johansson II, Yousoo Han, Douglas J. Gardner   +3 more
wiley   +1 more source

Research on gas-liquid coupled flow field dynamics and atomization characteristics of multi-duct sprayers based on CFD. [PDF]

Front Plant Sci
Li J, He H, Fan H, Lie Y, Li Y, Cao Y.
europepmc   +1 more source

Patterns of interspecific variation in labial microarchitecture among anthropoid primates and the evolution of the hominin lips

The Anatomical Record, EarlyView.
Comparative histological and semi‐automated image analysis of primate lips: Masson's trichrome‐stained sagittal sections were segmented to quantify the connective tissue, adipose, and muscular components, enabling interspecific comparisons of labial architecture.
Liat Rotenstreich, Kfir Eliyahu, Nir Edery, Lior Moss, Saleem Eben Bari, Assaf Marom   +5 more
wiley   +1 more source

Simulation-Based Trajectory for Non-Planar Scaffold Printing on Irregular Patches Using Robotic Arm. [PDF]

Bioengineering (Basel)
D'Alessandro S, Cidonio G, Ruocco G, Marinozzi F, Bini F.   +4 more
europepmc   +1 more source