Results 41 to 50 of about 105,767 (295)
Advanced Engineering Materials, EarlyView.A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann +2 more
wiley +1 more source
Active aerodynamics control of simplified vehicle body in a crosswind condition
The Journal of Engineering, 2020 In this study, the authors used a steady jet from a slit nozzle to control the bi-stable aerodynamics of a simple vehicle model under crosswind conditions.
Takuji Nakashima +6 more
doaj +1 more source
Erosive Intensity Measurements of Cavitating Jet [PDF]
, 2001 Cavitating jets are widely used for cleaning, cutting, improving material strength and so forth. This paper describes the erosive intensity measurement of a cavitating jet with various nozzle configurations.
Kato, Hiroharu, Yuya, Shimomura
core
Advanced Engineering Materials, EarlyView.The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos +11 more
wiley +1 more source
CFD study on nozzle cooling structure for a wind tunnel of high temperature and long operation time
工程科学学报, 2016 A wind tunnel of high temperature and long operation time requires the use of cooling techniques,so we need design cooling channels on the nozzle. In this paper,rectangular cooling channels of high cooling efficiency were used to study the factors ...
HE Ning, YANG Hai-bo, SUN Dong-bo
doaj +1 more source
Orthogonal Optimization Research on Various Nozzles of High-Speed Centrifugal Spinning
Frontiers in Bioengineering and Biotechnology, 2022 High-speed centrifugal spinning is a burgeoning method of fabricating nanofibers by use of the centrifugal force field. This article studied four different spinning nozzles, which were called stepped nozzle, conical-straight nozzle, conical nozzle, and ...
Zhiming Zhang +6 more
doaj +1 more source
Effects of Gravity and Non-Perpendicularity during Powder-Fed Directed Energy Deposition of Ni-Based Alloy 718 through Two Types of Coaxial Nozzle [PDF]
, 2020 The consequences of gravity and the nozzle inclination angle in the powder-fed Directed Energy Deposition (DED) process were examined in this study.
Alberdi, Amaia +3 more
core +2 more sources
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Biotechnologie, Agronomie, Société et Environnement, 2016 Study of the potential for the use of controlled droplet application (CDA) upon cereal crops. A review. Introduction. Controlled droplet application (CDA) has the advantage both of the reduction in the span of droplet size distribution and in the volume ...
Ouled Taleb Salah, S. +5 more
doaj
Research on flow field characteristic of close-coupled gas atomizing nozzles
Fenmo yejin jishuThe atomization nozzle is the core component for the metal powder preparation by close-coupled gas atomization method. The pressure at the tip of the melt delivery tube and the stagnation point is very important for the smooth outflow of the molten metal
BAN Wei +4 more
doaj +1 more source