Results 61 to 70 of about 63,661 (205)
Advanced Engineering Materials, EarlyView.Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Nanoindentation Criteria for Combinatorial Thin Film Libraries
Advanced Engineering Materials, EarlyView.Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley +1 more source
Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures
Advanced Engineering Materials, EarlyView.This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
Numerical Exploration of Thermal Shock Resistance in MgO–C Refractories
Advanced Engineering Materials, EarlyView.A mesostructure‐resolved numerical framework is developed to evaluate the thermal shock resistance of MgO–C refractories. By modeling interface debonding under rapid temperature changes and introducing a modified thermal shock parameter that accounts for mesocracks, the study shows how graphite content and aggregate size influence thermal shock ...
Jishnu Vinayak Gopi +3 more
wiley +1 more source