Results 21 to 30 of about 9,643,739 (297)
A new kinetic model for predicting polyamide 6-6 hydrolysis and its mechanical embrittlement [PDF]
, 2012 PA 6-6 hydrolysis at 60, 70, 80 and 90 °C in distilled water has been studied by Fourier transform infrared spectroscopy, viscometry in molten state, differential scanning calorimetry and uniaxial tensile testing.
COLIN, Xavier +3 more
core +1 more source
e-Polymers, 2020 Mechanical and tribological properties of nylon 6 and nylon 6/h-BN composites were investigated in this paper. Tensile, hardness, and impact tests were carried out for mechanical properties, while wear tests on pin-on-disc were carried out for ...
Randhawa Kawaljit Singh, Patel Ashwin D.
doaj +1 more source
Journal of Materials Research and Technology, 2021 Conductive fibers are an important part of wearable electronic devices or smart textiles while several grand challenges have to be still overcome. In this study, we describe a simple and efficient method to prepare a copper layer on nylon 6 fabrics by ...
Jhu-Lin You +4 more
doaj +1 more source
Sensors, 2009 We have prepared electrospun Nylon-6 nanofibers via electrospinning, and adsorbed multi-walled carbon nanotubes (MWCNTs) onto the surface of Nylon-6 fibers using Triton® X-100 to form a MWCNTs/Nylon-6 nanofiber composite.
Velmurugan Thavasi +2 more
doaj +1 more source
Spot Lap Joining of Titanium G2 to Nylon 6 by Nylon Extrusion via Friction Forming Technique
Journal of Techniques, 2021 To join sheets of commercial pure titanium grade 2 and nylon 6 polymer, friction lap spot welding (FLSW) was proposed. The titanium sheets were drilled to create a 3.5mm diameter hole, which was then threaded with M4.
Hashim Hasan Shareef, Ammar A. Hussain
doaj +1 more source
Thermal oxidation kinetics of additive free polyamide 6-6 [PDF]
, 2013 Thermal aging of an additive free PA 6-6 has been elucidated at 90, 100, 120, 140, 150 and 160 C in airventiled ovens by Fourier transform infrared spectrophotometry, viscosimetry in molten state and uniaxial tensile testing.
BEN HASSINE, Mouna +3 more
core +1 more source
[Letter to the editor] Ethylene emitted by nylon membrane filters questions their usefulness to transfer plant seedlings between media [PDF]
, 2011 Transfer of seedlings between media is a time-consuming process because the traditional, widely used method involves using forceps to transfer the plantlets one by one. The previously reported solution to avoid such a laborious procedure is the use
Sirko, Agnieszka +4 more
core +1 more source
Influence of boric anhydride reinforcement on mechanical properties and abrasive wear of nylon 6
Materials Research Express, 2020 To investigate the influence of boric anhydride (B _2 O _3 ) on mechanical properties of nylon 6, tensile, hardness and impact test were carried out. Average tensile strength along with percentage elongation and modulus of elasticity has been calculated ...
Kawaljit Singh Randhawa, Ashwin D Patel
doaj +1 more source
Nylon 6, 12/Cloisite 30B Electrospun Nanocomposites for Dental Applications [PDF]
Журнал Сибирского федерального университета: Серия Биология, 2016 In this study, nylon-nanoclay fibers were prepared by electrospinning. The electrospun membranes were characterized by fourier transform infra red spectroscopy (FTIR), electron microscopy, X-ray diffraction studies (XRD), contact angle and differential ...
Snigdha Sajeendra Babua +3 more
doaj
, 2018 Our study is focused on an efficient reduction of amide functional groups to secondary amine on Nylon 6 surface with borane–tetrahydrofuran (BH3–THF) complex, followed by N-alkylation with benzyl chloride (C6H5CH2Cl) which has been successfully used as a
Šubrtová Petra +7 more
core +1 more source