Results 71 to 80 of about 8,827,300 (340)
Fibras de Poliamida. Desarrollo y Previsiones. [PDF]
, 1987 Se describen las etapas más importantes del desarrollo de las fibras de poliamida, las diferencias entre el nylon 6.6 y el nylon 6, y las propiedades de otras fibras de poliamida comercializadas o de comercialización próxima.
Gacén Guillén, Joaquín
core
Proteins, Processing, and Properties of Adhesive Fluid Condensates Purified from Mussels
Advanced Functional Materials, EarlyView.Mussels exhibit an unmatched proficiency for adhering to wet surfaces in salty environments—a remarkable ability that could inspire new biomedical and technical glues. The fluid protein condensates used to form the underwater mussel glue are extracted, reconstituted and characterized with advanced spectroscopy and nanomechanical analysis, revealing ...
Mathieu D. Rivard +8 more
wiley +1 more source
Science and Technology of Advanced Materials, 2011 ZnO/Nylon 6 nanofiber mats were prepared by an electrospinning–electrospraying hybrid process in which ZnO nanoparticles were dispersed on the surface of Nylon 6 nanofibers without becoming completely embedded.
Narendiran Vitchuli, Quan Shi, Joshua Nowak, Kathryn Kay, Jane M Caldwell, Frederick Breidt, Mohamed Bourham, Marian McCord and Xiangwu Zhang
doaj
A comparison of the use of vacuum metal deposition versus cyanoacrylate fuming for visualisation of fingermarks and grab impressions on fabrics [PDF]
, 2014 Both vacuum metal deposition (VMD) and cyanoacrylate fuming (CAF) are techniques used to visualise latent fingermarks on smooth non-porous surfaces such as plastic and glass.
Bleay, Stephen +3 more
core +3 more sources
Upcycling of Disposable Face Masks into Water‐Resistant and Flame Retardant Foams
Advanced Functional Materials, EarlyView.Disposable mask waste is upcycled into lightweight polypropylene‐based foams with tunable porosity and composite architectures reinforced by ear‐loop fibers. The sustainable solvent‐based process enables upcycling rates of 91% and solvent recovery of >90%.
Jingjing Pan +3 more
wiley +1 more source
Interaction of CO2 laser-modified nylon with osteoblast cells in relation to wettability [PDF]
, 2009 It has been amply demonstrated previously that CO2 lasers hold the ability to surface modify various polymers. In addition, it has been observed that these surface enhancements can augment the biomimetic nature of the laser irradiated materials.
Arefi-Khonsari +34 more
core +1 more source
Advanced Functional Materials, EarlyView.Alumina growth narrows surface pores and seals non‐selective defects, enhancing selectivity while preserving the nanoporous graphene architecture. Additionally, the deposition enables gradient‐controlled structural modification, with intergrown alumina acting as a physical cross‐linker that stabilizes the laminar structure.
Junhyeok Kang +8 more
wiley +1 more source
Formation and properties of nylon 6 nanocomposites
Polímeros, 2003 Sodium montmorillonite clay consists of platelets, one nanometer thick with large lateral dimensions, which can be used to achieve efficient reinforcement of polymer matrices.
Fornes T. D., Paul D. R.
doaj
Effect of NaCl Solution Addition on Improving Some of the Physical Properties of Nylon 6 Solutions used for Electro spinning Purpose [PDF]
Engineering and Technology Journal, 2016 Nylon 6 / (0.5, 1, 1.5, 2 and 2.5) wt. % NaCl solutions were prepared for electrospinning technique. The electrical conductivity of polymeric solutionincreases directly with NaCl concentration from 3.8 (mS/ cm) for pure nylon solution to 12.7 mS/cm at ...
Fadhil A. Chayad +2 more
doaj +1 more source
The Nylon Scintillator Containment Vessels for the Borexino Solar Neutrino Experiment [PDF]
, 2007 Borexino is a solar neutrino experiment designed to observe the 0.86 MeV Be-7 neutrinos emitted in the pp cycle of the sun. Neutrinos will be detected by their elastic scattering on electrons in 100 tons of liquid scintillator. The neutrino event rate in
A. Goretti +49 more
core +3 more sources