Results 161 to 170 of about 34,598,226 (325)

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

A national study of substance use: Demonstrated use of recommendations for best practice online data collection. [PDF]

PLoS One
Bontemps AP, Pridgen BE, Wagner WP, Cropsey KL.   +3 more
europepmc   +1 more source

An Exploration of Stress: Leveraging Online Data from Crowdsourcing Platforms. [PDF]

Front Artif Intell, 2021
Roddy J, Robinson S.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Measuring global migration flows using online data. [PDF]

Proc Natl Acad Sci U S A
Chi G, Abel GJ, Johnston D, Giraudy E, Bailey M.   +4 more
europepmc   +1 more source

An Online Data Visualization Feedback Protocol for Motor Imagery-Based BCI Training. [PDF]

Front Hum Neurosci, 2021
Duan X, Xie S, Xie X, Obermayer K, Cui Y, Wang Z.   +5 more
europepmc   +1 more source

Accurate Online Data Application

Abstract With the increasing demand for high-precision, low-latency indoor localization in IoT and smart environments, the efficient online processing of CSI data has become a pressing challenge. While Chap. 4 focused on offline fingerprint updates, this chapter turns to online applications, aiming to ensure accurate and rapid localization in
Xiaoqiang Zhu, Yuan Liu, Chunpeng Wang
openaire   +1 more source

Online gaming, regulation, and big data [PDF]

, 2015
Auer, M, Griffiths, MD
core