Results 121 to 130 of about 888,059 (303)
Near-field projection optical microscope (NPOM) as a new approach to nanoscale super-resolved imaging. [PDF]
Sci Rep, 2023 Sanjeev A +4 more
europepmc +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh +3 more
wiley +1 more source
Facile Construction of a Laser Scanning Optical Beam Induced Current Microscope
IEEE Photonics JournalWe report on the design and construction of a laser scanning optical beam-induced current (OBIC) microscope by assembling cost-effective commercial optical and electronic hardware components and developing data acquisition and control software in LabVIEW.
Ankita Buragohain +6 more
doaj +1 more source
Retracted: Optical Microscope Rehabilitation Nursing Study of Anterior Cruciate Ligament Injury through Lateral Knee Incision Based on Medical Internet of Things. [PDF]
Appl Bionics Biomech, 2023 And Biomechanics AB.
europepmc +1 more source
An integrated single- and two-photon non-diffracting light-sheet microscope
, 2017 We describe the apparatus of a fluorescence optical microscope with both single-photon and two-photon non-diffracting light sheets excitation for large volume imaging.
Chiu, Hoi Chun +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh +6 more
wiley +1 more source
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, EarlyView.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart +3 more
wiley +1 more source