Results 141 to 150 of about 4,795,126 (305)

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khaleghian, Anahita Emami   +3 more
wiley   +1 more source

Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing

Advanced Engineering Materials, EarlyView.
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Resolution enhancement methods in optical microscopy for dimensional optical metrology

Journal of the European Optical Society-Rapid Publications
In this paper, we discuss several enhancement approaches to increase the resolution and sensitivity of optical microscopy as a tool for dimensional nanometrology.
Nouri Mohammad, Olivero Paolo, Kroker Stefanie, Käseberg Tim, Ruo-Berchera Ivano, Bodermann Bernd, Tyagi Himanshu, Roy Deb, Mukherjee Deshabrato, Siefke Thomas, Hansen Poul Erik, Rømer Astrid Tranum, Valtr Miroslav, Aprà Pietro, Petrik Peter   +14 more
doaj   +1 more source

Nanostructuring of glass micro-nanowires

In the past decade, glass fiber tapers with micron or sub-micron diameter have attracted much attention and found a wide range of applications in optics [1] including mode filtering, supercontinuum generation, high-Q resonators and resonant sensing ...
Brambilla, G., Ding, M.
core  

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Bimetallic (NiFe) and Trimetallic (NiFeCr) Nanoalloys from Metal Oxides Using a Microwave Hydrogen Plasma

Advanced Engineering Materials, EarlyView.
Bimetallic (NiFe) and trimetallic (NiFeCr) nanoalloys (NAs) are synthesized using corresponding oxide mixtures using microwave hydrogen plasma within a few milliseconds. The process simultaneously 1) reduces metal oxides to metals; 2) downsizes the particles from micrometers to nanometers; and 3) blends the metals to form NAs.
Sachin Kumar, Mohammad Kazemi, Zichang Xiong, Thomas Cameron, Julian Held, Uwe Kortshagen   +5 more
wiley   +1 more source

Introduction to the special issue on optics in elastography and cell mechanics [PDF]

Journal of Innovative Optical Health Sciences, 2017
David D. Sampson, Giuliano Scarcelli
doaj   +1 more source