Results 161 to 170 of about 1,233,950 (356)

Advances in fibre optic based geotechnical monitoring systems for underground excavations

International Journal of Mining Science and Technology, 2019
Geotechnical stability is a major concern for the long-term safety and integrity of underground infrastructures such as tunnels, railway stations, mine shafts and hydraulic power chambers.
Hongkui Gong, Mehmet S. Kizil, Zhongwei Chen, Moe Amanzadeh, Ben Yang, Saiied M. Aminossadati   +5 more
doaj  

Graphene coated micro/nano fiber gas sensing mechanism and SF6 decomposition component SO2 detection

电力工程技术
Accurate and effective monitoring of SF6 decomposition components inside the gas-insulated equipment （GIE） is crucial for the equipment fault diagnosis and condition assessment.
Yin ZHANG, Ao CHEN, Wenwen YU, Guozhi ZHANG, Yijie CAI, Xiaoxing ZHANG   +5 more
doaj   +1 more source

Femtosecond Single‐ and Double‐Pulse Fabrication of Periodic Nanostructures on Stainless Steel for Surface‐Enhanced Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
Periodic submicron features are fabricated on 304 stainless steel using single and double femtosecond laser pulses. By adjusting polarization, fluence, and inter‐pulse delay, 1D and 2D nanostructures are formed. Enhanced hydrophobicity and dense surface‐enhanced Raman spectroscopy hotspots enable analyte detection down to 10−10 M with good ...
Balaji Baskar, Atiqul Islam Ahad, Carla Berrospe‐Rodriguez, Guillermo Aguilar   +3 more
wiley   +1 more source

Optical Performance Monitoring: from direct detection to coherent optical communication systems

, 2012
Chao Lü, Alan Pak Tao Lau, Qi Sui, Fasial Khan, Zhenhua Dong   +4 more
openalex   +2 more sources

Optical performance monitoring at 160Gb/s via slow light enhanced third-harmonic generation in silicon photonic crystal waveguides [PDF]

, 2009
Bill Corcoran, Christelle Monat, Mark Pelusi, Christian Grillet, Thomas P. White, Liam O’Faoláin, Thomas F. Krauss, Benjamin J. Eggleton, David Moss   +8 more
openalex   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Additive Manufacturing of Highly Alloyed Aluminum–Lithium

Advanced Engineering Materials, EarlyView.
Al–Li alloys, promising for future lightweight constructions due to their low density and high stiffness, are limited to 9 at% lithium in commercial forms because of segregation issues. To overcome this traditional limitation, powder bed fusion with an ultrashort pulse laser is used.
Lisa Matthäus, Hagen Peter Kohl, Dongmei Liu, Stephanie Lippmann, Stefan Nolte   +4 more
wiley   +1 more source

An Overview of Machine Learning-aided Optical Performance Monitoring Techniques

, 2021
Dativa K. Tizikara, Jonathan Serugunda, Andrew Katumba   +2 more
openalex   +2 more sources

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

Antimicrobial Titanium–Copper Alloys: The Role of Microstructure in Arc‐Melted Compositions

Advanced Engineering Materials, EarlyView.
Copper‐containing titanium alloys show promise in combating orthopedic implant infections. This study explores the influence of heat treatment on Ti‐11.5Cu and Ti‐33Cu alloys, revealing that larger Ti2Cu precipitates (≈5 μm) enhance antimicrobial efficacy through increased surface contact. Results suggest contact sterilization is the primary mechanism,
Daisy Rabbitt, Paraic O’Kelly, Victor M. Villapún, Luke N. Carter, Alexander J. Knowles, Sophie C. Cox   +5 more
wiley   +1 more source