Results 211 to 220 of about 19,271,700 (291)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

open access: yesAdvanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin   +12 more
wiley   +1 more source

An integrative computational approach for obstacle avoidance during action selection. [PDF]

open access: yesPLoS Comput Biol
Zhong S   +3 more
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

Full dynamic similarity experiments and predictive modeling of wind turbine aerodynamics across control strategies. [PDF]

open access: yesPNAS Nexus
Kurelek JW   +6 more
europepmc   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

open access: yesAdvanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi   +3 more
wiley   +1 more source

Adjusting Nucleation Chemistry for the Atomic Layer Deposition of Antimony Selenide on Metal Oxide Surfaces

open access: yesAdvanced Engineering Materials, EarlyView.
The ALD precursor bis(trimethylsilyl)selenide is simultaneously a substrate surface inhibitor. It allows for the growth of Sb2Se3 in combination with tris(dimethylamido)antimony, but also silylates surface hydroxyl groups on the substrate if such hydroxyls are present.
Pei‐Chun Liao   +9 more
wiley   +1 more source

Edible Cuttlefish Ink: Complex Chemistry, Structure, and Electrical Response

open access: yesAdvanced Engineering Materials, EarlyView.
An integrated approach of chemistry‐structure‐electrical properties is used to assess the potential of edible cuttlefish ink as a bio‐based conductive ink for printable electronics. Chromatography and Neutron Activation Analysis reveal a fascinating molecular and elemental diversity.
Camille Bour‐Cardinal   +5 more
wiley   +1 more source

Heavy-Atom Tunneling at Room Temperature Revealed by Instanton Theory. [PDF]

open access: yesAngew Chem Int Ed Engl
Mukherjee D   +2 more
europepmc   +1 more source

Home - About - Disclaimer - Privacy