Results 31 to 40 of about 16,267 (243)

Optimal Gearbox Ratio to Minimize the Power Converter Ratings in DFIG-Based Type-3 Wind Turbines

open access: yesIEEE Access, 2023
Type-3 wind turbines based on the doubly-fed induction generator with a partial-scale power converter are commonly implemented in wind energy conversion systems.
Hussain A. Hussain
doaj   +1 more source

Integrated Traction Control Strategy for Distributed Drive Electric Vehicles with Improvement of Economy and Longitudinal Driving Stability

open access: yesEnergies, 2017
This paper presents an integrated traction control strategy (ITCS) for distributed drive electric vehicles. The purpose of the proposed strategy is to improve vehicle economy and longitudinal driving stability.
Xudong Zhang, Dietmar Göhlich
doaj   +1 more source

All-Wheel-Drive Torque Distribution Strategy for Electric Vehicle Optimal Efficiency Considering Tire Slip

open access: yesIEEE Access, 2021
The existing energy management strategies for four-wheel-drive electric vehicles only take into account the vehicle energy consumption under static adhesion constraints. However, the front and rear axle loads transfer under dynamic conditions lead to the
Kaibin Cao   +6 more
doaj   +1 more source

Tire Slip H∞ Control for Optimal Braking Depending on Road Condition

open access: yesSensors, 2023
Tire slip control is one of the most critical topics in vehicle dynamics control, being the basis of systems such the Anti-lock Braking System (ABS), Traction Control System (TCS) or Electronic Stability Program (ESP).
Miguel Meléndez-Useros   +3 more
doaj   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

open access: yesAdvanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth   +6 more
wiley   +1 more source

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

open access: yesAdvanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares   +3 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

open access: yesAdvanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi   +3 more
wiley   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

A Study on the Influence of Bolt Arrangement Parameters on the Bending Behavior of Timber–Steel Composite (TSC) Beams

open access: yesBuildings, 2022
The present paper investigates the impact of bolt distance, bolt diameter, and the number of bolt rows on the bending performance of timber–steel composite (TSC) beams.
Ruiyue Liu   +4 more
doaj   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy