Results 141 to 150 of about 219,767 (260)

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

NuConf: a rotamer library for DNA and RNA and its implementation in the protein design software MUMBO. [PDF]

Sci Rep
Makarova MO, Stiebritz MT, Basturk D, Lemke B, Süss B, Muller YA.   +5 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

A 3D-printed phantom to validate subject orientation in 3D imaging and recordings. [PDF]

Front Neuroinform
Becq GJC, Montigon O, Keshmiri S, Delphin A, Galloux P, Mathieu H, Lemasson B, Barbier EL.   +7 more
europepmc   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Optimisation of Bioinspired Fibre Architectures for 3D-Printed Polymer Heart Valves via Melt Electrowriting (MEW) Using FE Modelling and Design of Experiments (FE-DOE). [PDF]

Biomimetics (Basel)
Hughes C, Johnston RD, Armfield D, McCarthy D, Klusak E, Growney E, Campbell E, Lally C.   +7 more
europepmc   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

First-principles simulation of spin diffusion in static solids using dynamic mean-field theory. [PDF]

Sci Adv
Gräßer T, Uhrig GS, Ernst M.
europepmc   +1 more source

Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors

Advanced Engineering Materials, EarlyView.
We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay, Xue Bai, Thomas Kister, Tobias Kraus   +3 more
wiley   +1 more source