Results 131 to 140 of about 950,634 (295)

Analisis Akar Penyebab Masalah dalam Meningkatkan Overall Equipment Effectiveness (Oee) Mesin Stripping Hipack III dan Unimach di PT Pfi [PDF]

, 2015
. Overall Equipment Efectiveness (OEE) is a calculation method used inTotal Productive Maintenance (TPM) to maximize the effectiveness of machinesin industrial facilities.
Alamsyah, F. (Firman)
core  

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Analysis of proper ink management impact on overall environmental equipment efficiency for sustainability

Scientific Reports
Printing as a process itself generates many environmental concerns. The paper addresses ink management in terms of environmental issues in the label printing industry, focusing on its environmental implications.
Krzysztof Krystosiak, Aldona Kluczek, Wojciech Werpachowski   +2 more
doaj   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Collaborative Optimization of a Matrix Manufacturing System Based on Overall Equipment Effectiveness

Chinese Journal of Mechanical Engineering
When several traditional flow-shop lines operate in parallel, the operation mode with no communication between production lines will no longer be the optimal production paradigm. This paper describes matrix manufacturing systems (MMS) in a general manner
Fengque Pei, Jianhua Liu, Cunbo Zhuang, Liang Zheng, Jiapeng Zhang   +4 more
doaj   +1 more source

Ursachenanalyse geringer Anlagenproduktivität/Logistic cause-and-effect relationships of Overall Equipment Effectiveness – Root Cause Analysis of Low Overall Equipment Effectiveness

wt Werkstattstechnik online
Zunehmender Kostendruck erfordert von Unternehmen Produktivitätssteigerungen, die sich mit der Overall Equipment Effectiveness (OEE) messen lassen. Die Produktionsplanung und -steuerung (PPS) bietet zwar zahlreiche Stellschrauben, doch aufgrund der hohen Systemkomplexität sind die Ursachen einer geringen OEE schwer zu finden.
Kira Welzel, Bendix Kirchhoff, Niklas Müller, Matthias Schmidt   +3 more
openaire   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source