Results 151 to 160 of about 2,903,217 (301)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Developments and Prospects of Profit Sharing and Employee Share Ownership in Europe

, 2002
Item does not contain fulltextFix ...
Poutsma, F.
core  

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

A Multi‐Scale Machine Learning Framework for the Inverse Design of High Entropy Alloys

Advanced Engineering Materials, EarlyView.
High‐entropy alloys offer vast potential for various applications, including electrocatalysis; however, their compositional complexity challenges conventional screening. We introduce an inverse‐design framework combining two neural networks to determine optimal compositions and reconstruct nanoparticle geometry from targeted properties and conventional
Mikael Takoutsin, Marta Campolucci, Nicolas de Andrade Ishiki, Nathan Mirgot, Nadir Zhamantay, Frédéric Kanoufi, Jennifer Peron, Jean Charlety, Emiliano Fonda, Valérie Briois, Marco Faustini, Maria‐Letizia De Marco, Christine Goyhenex, Ovidiu Ersen, Hervé Bulou   +14 more
wiley   +1 more source

The Impact of State and Foreign Ownership on Post-Transition Industrial Concentration: The Case of Polish Manufacturing [PDF]

This paper reports an analysis of the determinants of the level and changes in Polish industrial concentration in the early post-transition era. The empirical evidence is based on a panel of 144 Polish manufacturing industries over the period 1989-1993 ...
Barbara Roberts, Kevin Amess
core  

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source