Results 81 to 90 of about 192,135 (306)

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Oxidation Behavior of Non-Modified and Rhodium- or Palladium-Modified Aluminide Coatings Deposited on CMSX-4 Superalloy

Metals, 2018
Rhodium-modified as well as palladium-modified and non-modified aluminide coatings on CMSX-4 Ni-based superalloy were oxidized in air atmosphere at 1100 °C. Uncoated substrate of CMSX-4 superalloy was also oxidized.
Maryana Zagula-Yavorska
doaj   +1 more source

Properties of protective oxide scales containing cerium on Incoloy 800H in oxidizing and sulfidizing environments. I. Constant-extension-rate study of mechanical properties [PDF]

, 1988
The mechanical properties of ceramic coatings containing cerium oxide, prepared by the sol-gel method and used to protect Incoloy 800H against aggressive environments, are reported.
Fransen, T., Geerdink, B., Gellings, P.J., Haanappel, V.A.C.   +3 more
core   +2 more sources

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Preliminary study of a solar selective coating system using black cobalt oxide for high temperature solar collectors [PDF]

Black cobalt oxide coatings (high solar absorptance layer) were deposited on thin layers of silver or gold (low emittance layer) which had been previously deposited on oxidized (diffusion barrier layer) stainless steel substrates.
Mcdonald, G.
core   +1 more source

Nickel oxide photocathodes prepared using rapid discharge sintering for p-type dye-sensitized solar cells [PDF]

, 2016
This paper compares the photoelectrochemical performances of nickel oxide (NiO) thin films processed using two different sintering procedures: rapid discharge sintering (RDS) and conventional furnace sintering (CS).
Awais, Muhammad, Dini, Danilo, Dowling, Denis P., Vos, Johannes G.   +3 more
core  

Zinc oxide-nickel cermet selective coatings obtained by sequential electrodeposition [PDF]

, 2015
The investigation of pulse electrodepositing modes influence on crystal structure, morphology and optical properties of ZnO has revealed the conditions in which quasi-one-dimensional (1D) ZnO nanorod arrays are formed as separate nanorods.
Khrypunov, G. S., Kirichenko, M. V., Klepikova, K. S., Klochko, N. P., Kopach, A. V., Kopach, V. R., Lyubov, V. M., Melnychuk, E. E., Myagchenko, Y. O., Starikov, V. V., Tyukhov, I. I.   +10 more
core   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Superconducting HfO2-YBa2Cu3O7-δ nanocomposite films deposited using ink-jet printing of colloidal solutions [PDF]

, 2019
To reduce the fabrication costs while maximizing the superconducting and pinning properties of YBa2Cu3O7−δ (YBCO) nanocomposite films, the drop-on-demand ink-jet printing technique was used to deposit colloidal YBCO inks onto LaAlO3 substrates.
Cayado, Pablo, De Buysser, KlaartjeWE060019971151158010015719620000-0001-7462-2484FA099C70-F0ED-11E1-A9DE-61C894A0A6B4, Diez Sierra, Javier0001613836478020025526519722597110874BF0BCA4-E8D2-11E6-B221-4557AE28A064, Erbe, Manuela, Holzapfel, Bernhard, Hänisch, Jens, López Domínguez, PedroWE060001614587228020026030700000-0002-8222-6200B4C94416-1B14-11E7-B8CA-0F8DAD28A064, Nast, Rainer, Palau, Annaeditor, Rijckaert, HannesWE060000701271588020016851090000-0002-6078-291906192A44-F0EE-11E1-A9DE-61C894A0A6B4, Van Driessche, IsabelWE06WE51WE628010007010830000-0001-5253-3325F4614F2A-F0ED-11E1-A9DE-61C894A0A6B4   +10 more
core   +2 more sources