Cogent Engineering, 2023 The current research utilizes a low voltage scanning electron microscopy (LV-SEM) with an electron beam along with low loading energy of lower than 2.2 KeV to minimize damage and specimen surface charging. The NovaSEM, is used as an efficient tool in the
Mohammed M. Sabri +2 more
doaj +1 more source
Comparison of morphological, thermal and mechanical properties of PA12 Produced by filament melting method and commercial PA12 [PDF]
, 2023 Polimer malzemeler, dünya ekonomisinin çeşitli alanlarında yaygın olarak kullanılmakta ve özellikleri hızla gelişmektedir. Eklemeli imalat (Eİ) gibi yeni teknolojilerin ortaya çıkışı, polimer malzemeler ve kompozitler için daha yüksek performans ve ...
TAŞDEMİR, MÜNİR
core
Low Temperature Laser Sintering on a Standard System: First Attempts and Results with PA12 [PDF]
, 2021 The laser sintering process has been a well-established AM process for many years. Disadvantages of LS are the low material variety and the thermal damage of the unprocessed material.
Menge, D., Schmid, H.-J.
core +2 more sources
Comprehensive Review: Technological Approaches, Properties, and Applications of Pure and Reinforced Polyamide 6 (PA6) and Polyamide 12 (PA12) Composite Materials [PDF]
PolymersMichal Krbaťa +2 more
exaly +2 more sources
3D printing of anisotropic Sm–Fe–N nylon bonded permanent magnets
Engineering Reports, 2021 Fabricating a bonded magnet with a near‐net shape in suitable thermoplastic polymer binders is of paramount importance in the development of cost‐effective energy technologies.
Kinjal Gandha +7 more
doaj +1 more source
Thermal Influence of CNT on the Polyamide 12 Nanocomposite for Selective Laser Sintering
Molecules, 2015 The thermal influence of carbon nanotubes (CNTs) on the PA12 in the laser sintering process was assessed by physical experiments and a three dimensional simulation model.
Jiaming Bai +5 more
doaj +1 more source
Morphology Development in Novel Composition of Thermoplastic Vulcanizates Based on PA12/PDMS Reactive Blends [PDF]
, 2011 International audienceThe main objective of the present work was to tailor a new thermoplastic vulcanisate (TPV) composed of PA 12 as the thermoplastic phase and PDMS as the rubber phase. The PDMS was crosslinked by dicumyl peroxide (DCP). Interestingly,
Philippe Cassagnau +8 more
core +1 more source
Performance regulation of 3D-printed PA12 based on deep space extreme environment
Cailiao gongchengPA12 material has good thermal stability and radiation resistance， and has broad application prospects in deep space manufacturing. However， PA12 materials prepared by fused deposition modeling （FDM） on the ground generally have structural defects such ...
ZENG Yong +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 In a powder bed fusion (PBF) process where powder bed preheating is needed, the powder bed will be subjected to an aging issue, which limits the reuse of powders.
Anfu Guo +8 more
doaj +1 more source
Aging of PA12 Powder in Powder Bed Fusion
Applied Sciences, 2023 Powder Bed Fusion (PBF) is a popular additive manufacturing technology due to its high build resolution and ability to produce microscale geometries without the use of additional support. Despite the many benefits of PBF, there are still some limitations associated with the materials to be built. A critical industrial limit is the aging of PA12 powder,
Achille Gazzerro +3 more
openaire +3 more sources