Results 161 to 170 of about 3,658,729 (281)

Soliton dynamics, overlapping phenomena, multistability, and chaotic nature of a nonlinear model in relativistic wave mechanics. [PDF]

Sci Rep
Ullah MS, Amin MR, Usman T, Mahbub MAA.
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Advanced semi-analytical techniques for fractional shallow water wave models through the analogical structure of generalized ϕ-Caputo derivative operators. [PDF]

Sci Rep
Damag FH, Saad KM, Alshammari M, Saif A, Alsharafi MS, Zeren Y.   +5 more
europepmc   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Semi-analytical investigation of nonlinear time-fractional fluid behavior with ϕ-Caputo memory. [PDF]

Sci Rep
Al-Sawalha MM, Noor S, Yasmin H, Kafle J.   +3 more
europepmc   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Initial stress effects on fractional thermoelastic wave propagation in semiconductor media under three thermoelasticity theories. [PDF]

Sci Prog
Ramadan ME, Ahmed HM, Radwan T, Yildirim Y, Elsadek H, Ismail MF.   +5 more
europepmc   +1 more source

Non‐Additive Criteria Assessment in Sustainability Evaluation of High Entropy Alloys: A Toxicity‐Weighted Framework

Advanced Engineering Materials, EarlyView.
Sustainability assessment requires methodologies that appropriately distinguish between additive and non‐additive material properties. A toxicity‐weighted scoring system is developed and applied that accounts for the disproportionate influence of highly toxic constituents through nonlinear weighting functions, providing more realistic estimates than ...
Seth Mehalic, Oladele A. Ogunseitan, Julie M. Schoenung   +2 more
wiley   +1 more source

Riccati-based analytical framework for solving the potential Korteweg-de Vries equation. [PDF]

Sci Rep
Jawarneh Y, Mukhtar S, Islam S, Amadou Y.   +3 more
europepmc   +1 more source

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source