Results 151 to 160 of about 997,002 (273)

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

A density functional theory study of tyrosine-proton mediated transport in Ag-filamentary nanodevices. [PDF]

Smart Mol
Berco D.
europepmc   +1 more source

Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection

Advanced Engineering Materials, EarlyView.
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram, Thomas Koch, Vasiliki-Maria Archodoulaki   +2 more
wiley   +1 more source

Efficient simulation of plasma physics' time fractional modified Korteweg-de Vries equations. [PDF]

PLoS One
Alharthi NS.
europepmc   +1 more source

Modeling task systems using parameterized partial orders

International Journal on Software Tools for Technology Transfer (STTT), 2012
Fred Houben, G. Igna, F. Vaandrager
semanticscholar   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source

Do-Not-Attempt-Resuscitation Orders in Older Adult Patients With Out-of-Hospital Cardiac Arrest: A Single-Center Retrospective Study at an Urban University Hospital Emergency Department in Japan. [PDF]

Cureus
Toyosaki M, Ueno K, Sasaki J.
europepmc   +1 more source

Subgrain and Cavity Development during Creep of Al‐3.85%Mg

Advanced Engineering Materials, EarlyView.
Al‐3.85%Mg does form subgrains if crept at very high strains. This fact allows the unification of the creep description in two different alloys such as pure Al and Al–Mg alloys. It is classically considered that the creep mechanisms for type M (e.g., pure Al) and type A alloys (e.g., Al–Mg alloys) are different.
Augusta Isaac, Itziar Serrano‐Munoz, Aleksander Kostka, Martinus Putra Widjaja, Gaspar González‐Doncel, Giovanni Bruno, Ricardo Fernández   +6 more
wiley   +1 more source

Computationally Efficient DFT-Based Sampling of Ion Diffusion in Crystalline Solids. [PDF]

J Chem Theory Comput
Gustafsson H, Schwarz F, Smolders T, Barthel S, Mace A.   +4 more
europepmc   +1 more source