Results 11 to 20 of about 412,295 (305)
Particle Board and Oriented Strand Board Prepared with Nanocellulose‐Reinforced Adhesive [PDF]
Journal of Nanomaterials, 2012 Adhesives on the basis of urea‐formaldehyde (UF) and melamine‐urea‐formaldehyde (MUF) are extensively used in the production of wood‐based panels. In the present study, the attempt was made to improve the mechanical board properties by reinforcing these adhesives with cellulose nanofibers (CNFs).
Stefan Veigel +3 more
openaire +1 more source
Phase behaviour of hard board-like particles [PDF]
Soft Matter, 2017 We examine the phase behaviour of colloidal suspensions of hard board-like particles (HBPs) as a function of their shape anisotropy, and observe a fascinating spectrum of nematic, smectic, and columnar liquid-crystalline phases, whose formation is entirely driven by excluded volume effects.
Alejandro Cuetos +3 more
openaire +5 more sources
SIFAT PAPAN PARTIKEL DARI LIMBAH EKSPLOITASI
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 The result of a study on the properties of particle board made from logging waste is reported in this paper. The wood species used in the study as raw material for particle board are meranti (Shorea sp.), ramin (Gonystylus bancanus Kurz.) and combination
Rozak Memed, I M Sulastiningsih
doaj +1 more source
PENGARUH PENYADAPAN DAN KADAR PEREKAT TERHADAP SIFAT PAPAN PARTIKEL TUSAM
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 The result of a study on the properties of particle board made from pine wood is reported in this paper. The pine as raw material was classified into three groups i.e. tapped, untapped, and combination of them. The particle board was
Rozak Memed +2 more
doaj +1 more source
The wear characteristics of cemented tungsten carbide tools in machining oil palm empty fruit bunch particleboard [PDF]
, 2009 A series of machining experiments on the Oil Palm Empty-Fruit Bunch (OPEFB) particle board were carried out using tungsten carbide tools, to ascertain the predominant mechanism of tool wear when machining this material.
Ma, T. P. +3 more
core +2 more sources
Jurnal Ilmu Kehutanan, 2008 Utilization of Nypa Fruit Flour (Nyfa Fruticans Wurmb) as an Extender in Urea Formaldehyde Adhesive for Particle Board Nipah fruit (Nyfa Fruticans Wurmb) is a seasonal forest product abundantly produced in each season.
Noor Mirad Sari +2 more
doaj +1 more source
Influence Of Varying Mix Design And Fiber Length On The Properties Of Water Hyacinth Particle Board
PUP Journal of Science and Technology, 2015 This study is focused on the investigation of the influence of varying mix design and fiber length on the properties of water hyacinth particleboard.
Melito Baccay
doaj +1 more source
Jurnal Pascapanen dan Bioteknologi Kelautan dan Perikanan, 2007 Penelitian pemanfaatan limbah padat rumput laut (Gracilaria sp) sebagai bahan baku untuk pembuatan papan partikel telah dilakukan. Empat perlakuan waktu pengempaan digunakan untuk mengetahui optimasi proses.
Diini Fithriani +2 more
doaj +1 more source
Characterizing Particle Board Made of Oil Palm Empty Fruit Bunch Using Central Composite Design
Makara Journal of Science, 2018 Particle board was made using processed oil palm empty fruit bunch and casein glue. This research used two factor variables and eight response variables to determine the best matrix/filler ratio and compression pressure for particle board production. The
Mirna Rahmah Lubis +3 more
doaj +1 more source
A Study on the utilization of coffee grounds for particle board
Journal of Aceh Physics Society, 2021 Abstrak. Penelitian ini bertujuan untuk membuat papan partikel dengan menggunakan limbah ampas kopi dan resin epoksi sebagai perekat. Komposisi resin epoksi divariasikan yaitu 5, 10, 15 dan 20 vol.% untuk masing-masing partikel ampas kopi berukuran 20 ...
Cut Rizka Maulida +2 more
doaj +1 more source