Results 111 to 120 of about 164,346 (296)
IEEE Access, 2018 In this paper, a passivity and fault alarm-based hybrid controller is designed for a Markovian jump delayed system with actuator failures. First, a passive condition is given, and a type of hybrid controller that combines with robust and fault-tolerant ...
Jian-Ning Li +3 more
doaj +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions
Advanced Engineering Materials, EarlyView.This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Lossy Coupling Matrix Synthesis Approach for the Realization of Negative Group Delay Response
IEEE Access, 2018 In this paper, a systematic synthesis approach is proposed for achieving negative group delay responses using lossy coupling matrix. It is mathematically proved that, for a passive and reciprocal network, loss is the necessary condition to realize a ...
Ranjan Das, Qingfeng Zhang, Haiwen Liu
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
MetalsThis study examined the effects of laser shock peening (LSP) and LSP without protective coating (LSPwC) on the microstructure and corrosion behavior of 304L stainless steel using cyclic polarization testing.
Richard Chiang, Vijay K. Vasudevan
doaj +1 more source