Results 111 to 120 of about 4,593 (266)

Feeding‐line‐based decoupling patch antennas

open access: yesIET Microwaves, Antennas & Propagation
Mutual coupling among multiple antennas has been a problem needed to be tackled in multiple‐input‐multiple‐output (MIMO) systems. A decoupling method based on short decoupling feeding lines (DFLs) for MIMO patch antennas is proposed.
Hui Gu   +4 more
doaj   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

open access: yesAdvanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir   +5 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

open access: yesAdvanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho   +8 more
wiley   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

open access: yesAdvanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva   +2 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

open access: yesAdvanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca   +9 more
wiley   +1 more source

Exploration of Pseudobinary Alloys (Al–Mn)‐(Co–Fe–Ni) to Design High‐Entropy and Compositionally Complex Alloys to Stabilize the τ Phase in Al–Mn‐Based Ferromagnetic Alloys

open access: yesAdvanced Engineering Materials, EarlyView.
This experimental study investigates the thermodynamic limits of the Al–Mn τ ferromagnetic phase within complex‐composition alloys (CCAs). Using nine rare‐earth‐free compositions, it explores a broad region of the pseudobinary AlMnCoFeNi system. The results reveal intricate links between composition, phase stability, and magnetic behavior, highlighting
Sacha Plagnol‐Chauzu   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy