Results 121 to 130 of about 1,161,775 (284)

Development and Preliminary In Vivo Study of 3D‐Printed Bioactive Glass Scaffolds with Trabecular Architecture

Advanced Engineering Materials, EarlyView.
This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov, Roberta Gabrieli, Avzal Akbarov, Nigora Nigmatova, Bekhzod Khabilov, Alessandro Schiavi, Martin Schwentenwein, Enrica Verné, Francesco Baino   +8 more
wiley   +1 more source

Trace Nickel Activated Biphasic Core‐CuOii/Shell‐CuOi Secondary Microspheres Enable Room Temperature Parts‐Per‐Trillion‐Level NO2 Detection

Advanced Engineering Materials, EarlyView.
An idea of designing novel sensors is proposed by creating appropriate Schottky barriers and vacancies between isomorphous Core‐CuOii/ Shell‐CuOi secondary microspheres and enhancing catalytic and spill‐over effects, and electronegativity via spontaneous biphasic separation, self‐assembly, and trace‐Ni‐doping.
Bala Ismail Adamu, Peipei Chen, Shafia Mukhtar Ibrahim, Mukhtar Lawan Adam, Attia Falak, Mokhotjwa Simon Dhlamini, Hanfu Wang, Lingxiang Jiang, Weiguo Chu   +8 more
wiley   +1 more source

Peak to Average Power Ratio Reduction of OFDM Signals Using Clipping and Iterative Processing Methods

Al-Khawarizmi Engineering Journal, 2008
One of the serious problems in any wireless communication system using multi carrier modulation technique like Orthogonal Frequency Division Multiplexing (OFDM) is its Peak to Average Power Ratio (PAPR).It limits the transmission power due to the ...
Ahmed K. Hassan
doaj  

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khalighian, Anahita Emami   +3 more
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source