Results 141 to 150 of about 290,122 (298)

Time delay neural networks reveal pressure-independent fault rupture processes in laboratory acoustic emission

Communications Earth & Environment
Fault nucleation and growth are central to earthquake hazard. Here we analyse fault development in Alzo granite under triaxial confining pressures of 5–40 MPa using a time-delay neural network applied to multi-parameter acoustic-emission data.
Thomas King, Sergio C. Vinciguerra
doaj   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Deep learning-based spatiotemporal multi-event reconstruction for delay line detectors

Machine Learning: Science and Technology
Accurate observation of two or more particles within a very narrow time window has always been a challenge in modern physics. It creates the possibility of correlation experiments, such as the ground-breaking Hanbury Brown–Twiss experiment, leading to ...
Marco Knipfer, Stefan Meier, Tobias Volk, Jonas Heimerl, Peter Hommelhoff, Sergei Gleyzer   +5 more
doaj   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Control and Filtering for Discrete Linear Repetitive Processes with H infty and ell 2--ell infty Performance [PDF]

, 2009
Repetitive processes are characterized by a series of sweeps, termed passes, through a set of dynamics defined over a finite duration known as the pass length.
Rogers, E, Paszke, W, Wu, L, Lam, J, Galkowski, K   +4 more
core  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Printed Integrated Logic Circuits Based on Chitosan‐Gated Organic Transistors for Future Edible Systems

Advanced Functional Materials, EarlyView.
Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco, Valerio Francesco Annese, Valerio Galli, Ilaria Penna, Debora Russo, Marina Veronesi, Rita Scarpelli, Stefania Sabella, Mario Caironi   +8 more
wiley   +1 more source