Results 201 to 210 of about 3,454,711 (304)

Impact of post-match fatigue on peak force in elite youth soccer players: Analysis of 48 to 72 hours post-match using the isometric mid-thigh pull exercise. [PDF]

Biol Sport
Pimenta R, Cunha L, Nakamura FY.
europepmc   +1 more source

Peak Wind Force Coefficients of Hoardings on Roof

Wind Engineers, JAWE, 2011
MASUYAMA, Yuka, NAKAMURA, Osamu, OKUDA, Yasuo, ITO, Shinji, KIKUCHI, Hirotoshi, NODA, Hiroshi, YOSHIDA, Akihito, UEMATSU, Yasushi   +7 more
openaire   +2 more sources

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

Advanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik, Liliana I. Duarte, Malgorzata G. Makowska, Roland Brütsch, Andrej Bullemer, Ana Diaz, Mirko Holler, Andreas Menzel, Johannes Bertsch, Pavel Trtik   +9 more
wiley   +1 more source

Reliability and Validity of the Strain Gauge "GSTRENGTH" for Measuring Peak Force in the Isometric Belt Squat at Different Joint Angles. [PDF]

Sensors (Basel)
Varela-Olalla D, Balsalobre-Fernández C, Romero-Moraleda B, Jiménez-Sáiz SL.   +3 more
europepmc   +1 more source

Nanoscale simultaneous chemical and mechanical imaging via peak force infrared microscopy. [PDF]

Sci Adv, 2017
Wang L, Wang H, Wagner M, Yan Y, Jakob DS, Xu XG.   +5 more
europepmc   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Changes in isometric mid-thigh pull peak force and symmetry across anterior cruciate ligament reconstruction rehabilitation phases. [PDF]

Front Rehabil Sci
Stofberg JPJ, Aginsky K, van Aswegen M, Kramer M.   +3 more
europepmc   +1 more source

Tomographic and multimodal scattering-type scanning near-field optical microscopy with peak force tapping mode. [PDF]

Nat Commun, 2018
Wang H, Wang L, Jakob DS, Xu XG.
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Correlation of Surface Morphology and Interfacial Adhesive Behavior between Cellulose Surfaces: Quantitative Measurements in Peak-Force Mode with the Colloidal Probe Technique. [PDF]

Langmuir, 2019
Lai Y, Zhang H, Sugano Y, Xie H, Kallio P, Kallio P.   +5 more
europepmc   +1 more source